CommScope e-POI Скачать руководство пользователя страница 47

Страница: 47 / 86

M0201ABK_uc

ERA® WCS and e-POI Subracks and Power Supply Unit Installation Guide

© June 2021 CommScope, Inc.

Page 47

Safely Working with ERA Hardware

Equipment Symbols Used / Compliance

Please observe the meanings of the following symbols used in our equipment and the compliance warnings

listed in

Table 10

Table 10.

Compliance Labels

Symbol

Compliance Meaning

—

FCC

For industrial (Part 20) signal booster:
WARNING: This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and

QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to

operate this device. Unauthorized use may result in significant forfeiture penalties, including

penalties in excess of $100,000 for each continuing violation.

—

ISED

WARNING: This is NOT a CONSUMER device. It is designed for installation by an installer approved

by an ISED licensee. You MUST have an ISED LICENCE or the express consent of an ISED licensee to

operate this device.
AVERTISSEMENT: Ce produit N'EST PAS un appareil de CONSOMMATION. Il est conçu pour être

installé par un installateur approuvé par un titulaire de licence d'ISDE. Pour utiliser cet appareil,

vous DEVEZ détenir une LICENCE d'ISDE ou avoir obtenu le consentement exprès d'un titulaire de

licence autorisé par ISDE.

To be sold exclusively to mobile operators or authorized installers - no harmonized frequency

bands, operation requires license. Intended use: EU and EFTA countries.
Indicates conformity with the RED directive 2014/53/EU and/or RoHS directive 2011/65/EU.

Indicates conformity with the RED directive 2014/53/EU and RoHS directive 2011/65/EU certified

by the notified body no. 0700.

Содержание e-POI























































































Результаты поиска

Содержание e-POI

Отзывы:

Бренды по названию

Популярные бренды

CommScope e-POI, Руководство по установке

Результаты поиска

Содержание e-POI

Отзывы:

Бренды по названию

Популярные бренды