background image

 

  

Installation Instruction for CMAX Antennas

 

 

Page 8 

Technical Support: 

http://www.commscope.com/wisupport 

M0149AMD_Installation_CMAX-

XXX-43X_Antennas 

 

4.5.  Outdoor Installation 

Note

: For outdoor use we recommend removing the plugs from the drain holes if the 

antenna is exposed to high humidity or rainfall. 

Do not remove the plugs if the antenna is mounted other than bottom 

down, that means the drain holes showing to the ground. For the top and bottom of the 

antenna observe the arrow labeling at the rear side. Otherwise water might penetrate into 

and, therefore, damage the antenna. 
Remove the plugs from the drain holes at the bottom of the antenna with a knife or a flat 

screwdriver. The below indicates the location of the drain holes, design and/or size of the 

antenna may be different.

 

 

 

Version 

Changes 

Release Date 

M0149AMA 

First release 

11-March-2019 

M0149AMB 

CMAX-DMH3030-43V53 removed 

28-March-2019 

M0149AMC 

CMAX-DM60X-43i53 added 

17-July-2019 

M0149AMD 

US  types and optional pole mounting kit added 

06-May-2020 

 

©  Copyright 2020 CommScope, Inc. 
All  rights reserved. 

All  information contained in this manual has been revised thoroughly. Yet CommScope accepts no liability for any omissions or faults. 

CommScope reserves the right to change all hardware and software characteristics without notice. 

Names  of products mentioned herein are used for identification purposes only and may be trademarks and / or registered trademarks of 

their respective companies. 

No  parts of  this publication may be reproduced, stored in a retrieval  system,  transmitted in any form  or  by  any means, electronical, 

mechanical photocopying, recording or otherwise, without prior written permission of the publisher. 
CommScope, 06-May-2020 

Содержание CMAX-DMW3060-43i53









Отзывы: