Command Light KL409D Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 40

Command Light KL409D Скачать руководство пользователя страница 15

USER GUIDE

15

Electrical Wiring

Please Note

: Detailed internal wiring schematics are located at the back of this user guide.

Run the control wire from the control box holster to the

KNIGHT

SLIM

.

Run the power wire from the breaker box or generator to the

KNIGHT

SLIM

. An 20 Amp breaker is

recommended on AC models.

Make the control connections in the

KNIGHT

SLIM

relay box.

The Model KL409D series

KNIGHT

SLIM

comes pre-wired to connect to 115 VAC.

12 VDC

Holster Wiring

Determine if an elevated warning device will be used in conjunction with the light tower. If a warning

device will be used, use the wiring diagram on the next page, otherwise, use the wiring diagram in the

back of the user guide.

After routing the control cable into the holster through the sealing connector, attach individual wires to

the provided connectors and insert the connectors into the proper ports on the circuit board.

«
...
13
14
15
16
17
...
»

Содержание KL409D









































Отзывы:

Нет отзывов