3
3
USAGE
HEATER OPERATION:
Always operate the heater in the upright position following all
instructions and recommendations listed in this manual.
HEATER LOCATION:
Place the heater in the area of the room that
is coldest. Do not locate against walls or behind drapes or furniture.
HEATER CONNECTION:
Plug heater directly into 120 Volt
AC, 60Hz wall outlet. Be sure plug fits tightly in outlet. A loose
connection may cause overheating and damage to the plug
or heater.
NOTE:
To prevent overloading a circuit, do not plug the heater into
a circuit that is servicing other electrical needs.
OPERATING INSTRUCTIONS:
• Plug the power cord into a wall outlet (120V AC, 60Hz). Connect
heater to properly grounded outlets only. Power Indicator Light will
be illuminated and the unit will be in its standby state. In this state,
“- -” is shown on the display and indicates that the unit is on but
not heating.
TURN THE HEATER ON OR OFF BY PRESSING ( ):
Pressing the ON/OFF button once will select the Low Heat (750W)
setting, indicated by the illumination of the Low Heat Indicator Light.
Pressing the ON/OFF button a second time will select the High
Heat (1,500W) setting, indicated by the illumination of the High Heat
Indicator Light.
Pressing the ON/OFF button a third time will return the heater to the
standby state. Make sure the heater is in the standby state before
unplugging. The heater should be unplugged when not in use.
NOTE:
During the heater’s initial use, you may experience a slight
odor or smoking. This is the result of the heating element lubrication
“burning off”. This is normal and will go away after a few minutes
of use.
NOTE:
Heater will function in the Low or High heat setting
independently of the thermostat, when the thermostat is set to
“00C” or “00F”.
NOTE:
The temperature value displayed in both heat settings is the
current ambient temperature.
TEMPERATURE UNITS:
To switch between Celsius and Fahrenheit units, press the
MODE button once. The digital display will blink 3 times and then
automatically switch. Temperature will reset to the default setting
when units are changed.
SETTING THE THERMOSTAT:
When the heater is in the heat setting (either Low or High), press
the UP/DOWN button once to select the thermostat option. This
is indicated by the illumination of the Temperature Indicator Light
and by a flashing “00C” on the display (or “00F”, depending on
the selected units). At this time, press the UP/DOWN buttons to
raise or lower the temperature set point.
Once the desired temperature is reached, press the MODE
button once to select the Timer option or twice to exit both
options – this will return the display to the ambient temperature.
Alternatively, the unit will automatically save and exit after
15 seconds of inactivity, returning the display to the ambient
temperature. After exiting, the Temperature Indicator Light will
remain illuminated to show that the thermostat option is active.
NOTE:
When the ambient air temperature is equal to or below
the thermostat set point, the heater will automatically turn on.
If the ambient air temperature is greater than the thermostat
set point, the heater will turn
off – in this state, the Power
and Temperature Indicator
Lights will remain illuminated
and the ambient temperature
will be displayed.
SETTING THE TIMER:
When the heater is in the
heat setting (either Low or
High), press the MODE button
two times to select the timer
option. This is indicated by
the illumination of the Timer
Indicator Light and by a
flashing “00H” on the display.
At this time, press the UP/DOWN buttons to set the length of
time for the heater to run. The timer adjustment range is from
1 to 12 hours.
Once the desired time is reached, press the MODE button once
to exit – this will return the display to the ambient temperature.
Alternatively, the unit will automatically save and exit after
15 seconds of inactivity, returning the display to the ambient
temperature. After exiting, the Timer Indicator Light will remain
illuminated to show that the timer option is active.
To turn the timer off, select the timer option using the MODE button
and adjust the time displayed to “00H”.
NOTE: When the timer has reached its setting, the timer indicator
light will turn off and the heater will automatically turn off, returning
to the standby state.
USING THE THERMOSTAT AND TIMER AT THE SAME TIME:
It is possible to have both the thermostat and timer active at the
same time. To do so, follow the instructions under “Setting the
Thermostat”. Once the desired temperature has been reached,
press the MODE button once to select the timer option and follow
the instructions under “Setting the Timer”.
NOTE:
When both the thermostat and timer options are active, the
heater will remain on until the timer setting is reached. When the
timer has reached its setting, the heater will automatically turn off,
returning to the standby state.
CAUTION INDICATOR LIGHT:
When overheating occurs, the Caution Indicator Light will illuminate
and the heater will turn off immediately. Refer to the ‘Safety
Features’ section for heater reset instructions.
