background image

23

LIGHTING INSTRUCTIONS

1. STOP! Read the safety information above. 

2. Turn control knob clockwise 

 to the “OFF” position (See Fig. 25). 

3. Wait five (5) minutes to clear out any gas. Then smell for gas, including  

    near the floor. If you smell gas, STOP! Follow “B” in the safety informa-

    tion above. If you don’t smell gas, go to the next step. 

4. Turn control knob counterclockwise 

 to the “PILOT” position.

    Depress control knob. 

5. With control knob depressed, push down on the ignitor button until the 

    pilot lights. The pilot is located behind the heater screen near the rear of 

    the burner.

• Do not attempt to light the pilot by hand.

6. Keep control knob depressed for (30) seconds after pilot lights. Release 

    control knob.

• If the control knob does not pop up when released, stop and immediately 

call a qualified service technician or gas supplier.

• If pilot goes out repeat steps 3 through 7. Wait (1) minute before attempt-

ing to light pilot again. If after several tries the pilot still goes out, turn the 

gas control knob clockwise 

 to the “OFF” position and call a qualified 

service technician.

7. Turn control knob counterclockwise 

 to desired setting.

Fig. 25 - Control Knob

Fig. 26 - Pilot

OPERATION

TO TURN OFF GAS TO APPLIANCE

1. Turn control knob clockwise         to the “OFF” position.

Shutting Off Burner Only (pilot stays lit )

Turn control knob clockwise         to the PILOT position.

THERMOSTATIC CONTROL OPERATION

The thermostatic control valve used on this model differs from standard thermostats. Standard ther-

mostats simply turn the burner on and off. The thermostat sensing bulb on the control valve used on 

this heater senses changes in room temperature and will vary the flame accordingly. When the room 

temperature exceeds the set temperature the burner will shut off completely. The unit will cycle back 

on as the room temperature drops below the set temperature. The control knob can be set to the de-

sired comfort level between 1 and 5.

  

   WARNING: 

Any glass doors shall be completely opened while appliance is in operation.

  

   WARNING: 

The fireplace screen must be in place while the appliance is in operation. 

 

LP PILOT

 

NG PILOT

Содержание GLD1856T

































Отзывы: