COMFORT-AIRE Century GUH80C045A3M Скачать руководство пользователя страница 10

Страница: 10 / 31

508096-01

Issue 2037

Page

of 3

Figure 6. Heating Components

Gaskets

Collector Box

Orifice Plate

Flue Transition

Pressure Switch

Combustion Air Inducer

Manifold And Gas Valve

Ignitor

Sensor

Rollout Switches

Cooling Fan On Time

The fan on time is 2 seconds and is not adjustable.

Cooling Fan Off Time

The control has a 45 second fan off delay after cooling

demand has been met. This delay is factory set and not

adjustable.

Ignitor (Figure 6)

GUH80C

units use a nitride ignitor made from a

proprietary ceramic material. To check ignitor, measure

its resistance and voltage. A value of 39 to 70

ohms indicates a good ignitor. Voltage to the ignitor

should be 102 - 132VAC. See Figure 9 for resistance

and voltage checks.

NOTE:

The

GUH80C

furnace contains electronic

components that are polarity sensitive. Make sure that

the furnace is wired correctly and is properly

grounded.

Flame Rollout Switches (Figure 6)

Flame rollout switch (S47) is a high temperature limit. Each

furnace is equipped with two identical switches. The limit

is a N.C. SPST manual-reset limit connected in series

with the integrated control A92. When S47 senses rollout,

the integrated control immediately stops ignition and

closes the gas valve. If unit is running and flame rollout is

detected, the gas valve will close and integrated control

will be disabled. Rollout can be caused by a blocked

heat exchanger, blocked flue or lack of combustion air.

The switch has a factory setpoint of 210°F and cannot

be adjusted. To manually reset a tripped switch, push the

reset button located on the control.

Flame Sensor (Figure 6)

A flame sensor is located on the left side of the burner

support. The sensor is mounted on the flame rollout plate

and the tip protrudes into the flame envelope of the left-

most burner. The sensor can be removed for service (clean

with steel wool) without removing any part of the burners.

During operation, flame is sensed by current passed

through the flame and sensing electrode. The integrated

control allows the gas valve to remain open as long as

flame signal is sensed.

Содержание Century GUH80C045A3M
































Результаты поиска

Содержание Century GUH80C045A3M

Отзывы:

Похожие инструкции для Century GUH80C045A3M

Бренды по названию

Популярные бренды

COMFORT-AIRE Century GUH80C045A3M, Руководство по обслуживанию

Результаты поиска

Содержание Century GUH80C045A3M

Отзывы:

Похожие инструкции для Century GUH80C045A3M

Бренды по названию

Популярные бренды