background image

Installing The Digital Station Board

In The FX Digital Communications System

Introducing The Digital Station Boards

The digital station board supports the operation of all Comdial proprietary digital multiline telephones.

Inventorying The Digital Station Boards

There are six models of station boards available for use.

FXSDS–04 supports four multiline and single-line proprietary digital telephones
FXSDS–08 supports eight multiline and single-line proprietary digital telephones
FXSDS–16 supports 16 multiline and single-line proprietary digital telephones
FXLDS–04 supports four multiline, large-display, proprietary digital telephones
FXLDS–08 supports eight multiline, large-display, proprietary digital telephones
FXLDS–16 supports 16 multiline, large-display, proprietary digital telephones

Complying With Underwriters Laboratories Regulations

Per The Underwriters Laboratories regulation 1950, be aware of the following precautions when installing
telephone equipment that is to be directly connected to the telephone company network:

Never install telephone wiring during a lightning storm.

Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the
network interface.

Use caution when installing or modifying telephone lines.

Avoid using a telephone (other than a cordless type) during an electrical storm—there may be a remote risk of
electrical shock from lightning.

Do not use the telephone to report a gas leak in the vicinity of the leak.

R

This manual has been developed by Comdial Corporation (the “Company”) and is intended for the use of its customers and service personnel. The information in this manual is subject to change without notice.
While every effort has been made to eliminate errors, the Company disclaims liability for any difficulties arising from the interpretation of the information contained herein.
The information contained herein does not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation, operation, or
maintenance. Should further information be desired, or should particular problems arise which are not covered sufficiently for the purchaser’s purposes, contact Comdial, Inside Sales Department,
Charlottesville, Virginia 22906.

Printed in U.S.A.

IMI89-267.02

11/98

Содержание FXLDS-04













Отзывы: