4
9
Daily Inspection
Periodic Inspection
Daily or Weekly
Once a Year
Combi Baby Keep Slim
Inspection Manual
This manual describes the details of "Daily Inspection" and "Periodic Inspection" required to use Combi Baby Keep Slim
safely and comfortably. Follow the contents of this manual and make sure to carry out daily or weekly inspection and pe-
riodic inspection every year correctly.
Daily inspections are carried out by visual and touch.If any abnormality is found
in the inspection, use a tool to perform the inspection depending on the case.
Daily inspection should be carried out daily or weekly. Inspections are done by visual and touch.
If any abnormality is found in the inspection, use a tool to perform the inspection depending on the point.
● If any abnormalities are found during inspection, stop using the product and contact your dealer to request repair.
Warning
Carry out daily inspection and periodic inspection once a year to ensure safety. Failure to do so may cause an injury or seri-
ous accident caused by undiscovered deterioration or damage to the product.
1
Phillips Screwdriver
No.2, No.3
Flat-Head Screwdriver
Wrench
(nominal 17MM)
Socket Wrench
Do not use the power tool when fasten-
ing the product. Make sure to tighten by
hand and do not use the power tool.
Any use of the power tool may result in
damage to the plastic part.
Required Tools
Prepare the following tools.
Caution
Each part is inspected every year using a tool.
As a result of the inspection, parts may need to be replaced.
*The stock period of the repair parts is 5 years after the final production.
Daily Inspection
A. Checking the Appearance
Common for Combi Baby Keep SlimF62/W62/W65 for train. (Below diagram is Combi Baby Keep Slim F62)
②
Looseness of the Guard
Confirm that there is no looseness in
the guard after shaking the guard to
left and right.
Also, confirm that there is no loosness
in the guard after open and close the
guard several times.
After the periodic inspection, enter the inspection
date on the inspection sticker affixed to the lower
cover.
D. Entering Inspection Date
B. Checking Missing or Loosening of Various Screws (when corner bracket is used)
C. Checking Appearance (Metal Parts)
After checking, assemble by the reverse procedure.
When assembling, use Phillips screwdriver No3 to make sure that main body fixing screws (8 locations) and lower
cover fixing screws (2 locations) are not missing or loosened.
After the assembly is completed, inspect it by referring to Daily Inspection (page 4).
❺
Checking Main Body Fixing Screws and Lower Cover Fixing Screws
*The corner bracket is sold separately.
Inspection Points
Inspection Method
Judgment Criteria
Handling of Defects
❹
Corner cover fixing screws
(Upper and lower 2 locations each)
Corner bracket fixing screws (4 locations)
❺
Main body fixing screws (8 locations)
Bottom cover fixing screws (2 locations)
Retightening
Retightening
Visual, Touch
(Phillips screw driver No2
、
No3
、
Wrench)
Visual, Touch
(Phillips screw driver No3)
No missing or looseness
Inspection Points
Inspection Method
Judgment Criteria
Handling of Defects
❻
Deformation or rust of main body frame
Discontinuation
of use
Visual
No deformation or rust
❼
Missing, loss, deformation, rust of screws
and metal fittings
Replacement
Visual
No disconnection, loss,
deformation, or rust
No missing or looseness
Use Phillips screwdriver
No2 for the corner cover
fixing screws (Upper and
lower 2 locations each)
and use Phillips screw
driver No3 or wrench to
check the corner bracket
fixing screws (4 locations)
❹
Checking Corner Cover Fixing Screws and Corner Bracket Fixing Screws.
③
Use a back cushion and a
flat-head screw driver to
remove the plastic caps (2 pcs),
then use a Phillips screwdriver
No3 to remove the lower cover
fixing screws (2 locations ) and
remove the lower cover.
*To disassemble the back
cushion, refer to "Back
Cushion Replacement
Procedure" on back cover.
①
Use a Phillips screwdriver
No3 to remove the main
body from the corner
bracket.
②
Inspection Points
Inspection Method
Judgment Criteria
①
Looseness of the main body
②
Looseness of the guard
③
Looseness of back cushion
Motion,
Visual and touch
Handling of Defects
Retightening (see page 6
and 9 of periodic inspection)
Motion,
Visual and touch
Motion,
Visual and touch
⑤
Scratches or breakage of the main body
⑥
Scratches or damage of the back cushion material
⑦
Soil on main body
⑧
Soil on back cushion material
Repair
Replacement
Repair
Replacement
Cleaning
Cleaning
Visual
Visual
Visual
Visual
No looseness when the main body
is being shaken.
When the guard is shaken by hand,
there should be no rattling.
When the back cushion is shaken by
hand, there should be no looseness.
No serious scratch or damage
④
Detachment of plastic cap
Replacement
Visual
No peeling or missing
No severe cut or damage
No soiling
No soiling
Body fixing screws
(8 locations)
Corner bracket
Corner cover
fixing screws
(2 locations)
Corner cover
Back side of
the main body
Back cushion
Bottom cover
fixing screws
(2 locations)
Plastic cap (2 pcs)
Corner bracket
fixing screws
(2 locations)
Corner bracket
fixing screw
（
4 locations)
Corner cover
Lower cover
Corner bracket
Inspection sticker
(Inspection S for 1-year silver)