manualshive.com logo in svg

Comar Systems CSA-300, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comar Systems CSA-300 Скачать руководство пользователя страница 31

Installation 

Page 31

4 Installation

The CSA-300 AIS transceiver has been designed for ease of installation. The transceiver is a ‘one box’ design 
containing both the transceiver and display. An external junction box is provided to simplify connection of 
sensor and display data wiring. A typical system and connection diagram is provided in Figure 32.

Figure 32 Typical AIS transceiver connection 

The main elements of installation are:

1.

Mount the transceiver and junction box in a suitable location.

2.

Install VHF antenna according to manufacturers instructions.

3.

Install the GPS antenna.

4.

Connect data interfaces.

5.

Apply power and configure the transceiver.

6.

Confirm correct operation.

7.

Complete the installation log.

GPS antenna

12/24V DC Supply

Pilot equipment

Optional PC

VHF antenna

Above decks

Below decks

Junction box

Displays

(ECDIS, RADAR)

Ship’s sensor data

(DGPS, GYRO, Heading)

Содержание CSA-300














































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды