ComAp intelilite nt amf20 Скачать руководство пользователя | Manualshive

Страница: 5 / 145

background image

InteliLite

NT

– AMF20/25, SW version 2.2, ©ComAp – September 2014

5

IL-NT-AMF-2.2-Reference Guide.pdf

General Guidelines

What describes this manual?

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTION

-

This manual contains important instructions for IL-NT

controllers family that shall be followed during installation and maintenance of the InteliLite NT genset
controllers.
It is intended for use by gen-set control panel builders and for everybody who is concerned with
installation, operation and maintenance of the gen-set.

This manual describes

„AMF 20/25“ software which is designed for single set stand-by applications.

What is the purpose of the manual?
This manual provides general information how to install and operate InteliLite-NT AMF20/25 controller.

This manual is dedicated for

Operators of gen-sets
Gen-set control panel builders
For everybody who is concerned with installation, operation and maintenance of the gen-set

!! Warnings !!

Remote control

InteliLite controller can be remotely controlled. In case of the work on the gen-set check, that nobody
can remotely start the engine.
To be sure:

Disconnect remote control via RS232 line
Disconnect input REM START/STOP

or

Disconnect output STARTER and outputs GCB CLOSE/OPEN and MCB CLOSE/OPEN

Because of large variety of InteliLite

NT

parameters settings, it is not possible to describe any

combination. Some of InteliLite functions are subject of changes depend on SW version.
The data in this manual only describes the product and are not warranty of performance or
characteristic.

InteliLite controller SW and HW versions compatibility

Be aware that IL-NT SW version 1.2.1 and older is not possible to use with IL-NT HW version 1.3 and
newer!!! Software IL-NT 1.3 is compatible with IL-NT hardware version 1.3 and older.

Symbols

Symbols used in this manual:

Grounding
point symbol

AC voltage
symbol

DC voltage
symbol

«
...
3
4
5
6
7
...
»

Содержание intelilite nt amf20


















































































































































Отзывы:

Нет отзывов

Похожие инструкции для intelilite nt amf20

Бренд: D-Link Страницы: 113

Бренд: D-Link Страницы: 146

Max Charge MC-624

Бренд: Balmar Страницы: 8

MAX CHARGE MC-614

Бренд: Balmar Страницы: 20

Бренд: Campbell Страницы: 8

Бренд: Campbell Страницы: 22

Бренд: National Instruments Страницы: 29

Бренд: Samson Страницы: 78

Бренд: NCR Страницы: 8

Бренд: Vaillant Страницы: 32

Бренд: Vaillant Страницы: 27

Бренд: Vaillant Страницы: 40

Бренд: Vaillant Страницы: 36

Бренд: Vaillant Страницы: 28

Бренд: Vaillant Страницы: 92

Бренд: Vanderbilt Страницы: 2

Extra Free RZB-02

Бренд: Zamel Страницы: 2

Бренд: Yamaha Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды