ComAp InteliLite MRS16 Скачать руководство пользователя

Страница: 133 / 632

InteliLite Global Guide

133

SNMP notifications

Except the request-response communication model, in which the communication is controlled by the Manager,

there are also messages that the Agent sends without any requests. These messages are called „Notifications“

and inform the Manager about significant events occurred in the Agent.

The controller can send notifications to two different SNMP Managers (two different IP addresses). The

addresses are to be adjusted in the CM-Ethernet setpoint group by the setpoints

SNMP Traps IP Address 1 (page

336)

and

SNMP Traps IP Address 2 (page 336)

. If the Manager address is not adjusted the particular notification

channel is off. The controller will send the notifications in format adjusted by the setpoint SNMP Trap Format.

Each notification (kind of event) is identified by an unique identifier (Trap ID in SNMPv1 or Notification OID

in SNMPv2). This unique identifier gives the specific meaning to the notification message, e.g. Protection 1.

level - Fuel Level - alarm activated.

All possible notifications and their identifiers are listed in the MIB table.

The notification message also contains controller name, serial number and textual description of the event.

6.2.2 MODBUS-RTU, MODBUS/TCP

MODBUS protocol is used for integration of the controller into a building management system

or for remote monitoring via 3rd party monitoring tools.

MODBUS-RTU can be used on serial interfaces (CM-RS232-485 module is required). The MODBUS-RTU

server must be activated by switching the setpoint

COM1 Mode (page 300)

COM2 Mode (page 301)

into

the Modbus position. The serial speed for MODBUS-RTU communication is to be adjusted by the setpoint

COM1 MODBUS Communication Speed (page 301)

COM2 MODBUS Communication Speed (page 302)

MODBUS/TCP can be used on the ethernet interface (CM-Ethernet module is required). Up to 2 clients can

be connected simultaneously. The MODBUS/TCP server must be activated by the setpoint

MODBUS Server

(page 335)

MODBUS, MODBUS/TCP protocol can be used simultaneously with Web connection and direct

ethernet/AirGate connection.

The MODBUS, MODBUS/TCP protocol is enabled alternatively with the SNMP protocol, so both protocols can

not be active simultaneously.

Addres space

The object address space is separated into several areas as described in the table below. The actual mapping of

specific controller data objects to specific MODBUS addresses, which depends on configuration, can be

exported into a text file from the appropriate controller archive using LiteEdit2015. There are several special

registers with fixed meaning (reserved registers) which are listed in a separate table in this chapter.

MODBUS

address

Meaning

Access

MODICON object

type

MODBUS function

0000 .. 0999

Binary objects

Read only

Discrete Inputs

1000 .. 2999

Values

Read only

Input Registers

Содержание InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды

ComAp InteliLite MRS16, Руководство пользователя

Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды