ComAp InteliDrive FLX LITE Скачать руководство пользователя

Страница: 78 / 228

ID-FLX Lite Global Guide

Events

specification

Protection

type

Information on binary

output available

(see List of LBO on page

198)

Description

protection comes active if the

running hours of the engine reach

this value.

ChrgAlternFail

WRN

YES

Failure of alternator for charging the

battery.

SprinklActive

WRN

The protection is active if the output

Sprinkler is closed.

Wrn RA15 fail

WRN

Warning alarm in case of lost

connection to remote annunciator

module.

Wrn ECU Alarm

WRN

ECU alarm list is not empty.

Low BackupBatt

WRN

RTC backup battery is flat.

6.2 History file

ID-Lite stores a record of each important event into the history file. The history file seats 255 records. When the

history file is full, the oldest records are removed.

Note:

To force history download in LiteEdit (direct, modem or internet) open History window and select History |

Read history command.

6.2.1 Record structure

Abbreviation

Historical value

Num

Number of historical event

Reason

Event specification

Date

Date of historical event in format DD/MM/YY

Time

Time of historical event in format HH:MM:SS

RPM

Engine speed

RPM3

Engine speed detected on BI3

UBat

Battery voltage

OilP

ID-Lite analog input 1 value (default Oil pressure)

EngT

ID-Lite analog input 2 value (default Water temperature)

FLvl

ID-Lite analog input 3 value (default Fuel level)

AI4

ID-Lite analog input 4 value

AI5

ID-Lite analog input 5 value

AI6

ID-Lite analog input 6 value

AI7

ID-Lite analog input 7 value

AI8

ID-Lite analog input 8 value

Содержание InteliDrive FLX LITE





































































































































































































































Результаты поиска

Содержание InteliDrive FLX LITE

Отзывы:

Похожие инструкции для InteliDrive FLX LITE

Бренды по названию

Популярные бренды

ComAp InteliDrive FLX LITE, Руководство пользователя

Результаты поиска

Содержание InteliDrive FLX LITE

Отзывы:

Похожие инструкции для InteliDrive FLX LITE

Бренды по названию

Популярные бренды