ComAp InteliDrive FLX LITE Скачать руководство пользователя

Страница: 181 / 228

ID-FLX Lite Global Guide

181

Setpoint group

AIO module

Related FW

2.5.0

Range [units]

0 .. 180 [s]

Default value

Step

Comm object

13661

Related applications

Description

Configuration

Protection

Under limit

Protection is activated only when measured value is under measured level.

Over limit

Protection is activated only when measured value is over measured level.

Undfls

Level 2 protection is activated by sensor fail too.

Ovfls

Level 2 protection is activated by sensor fail too.

Note:

Plug-in analog inputs protection alarms can be configured following way.

AnlInAIO4 del

back to List of setpoints

Group: Act. Calls/SMS

Note:

If a cellular network modem and/or internet bridge is connected to the controller, the controller can send

SMS messages and/or emails in the moment when a new alarm appears in the Alarm list. The message will

contain a copy of the Alarm list.

To enable this function, you should select with setpoints Yel Alarm Msg and Red Alarm Msg, which levels of

alarms shall be announced (red/yellow/both) and also enter valid cellular network phone number and/or e-mail

address to the setpoints TelNo/Addr Ch1 and TelNo/Addr Ch2. It is possible to put either number or e-mail to

both setpoints.

Note:

An internet module must be available for sending of e-mails. Similarly, a cellular network modem is

necessary for sending of SMS.

Note:

There are 5 attempts for any active call (SMS/E-Mail). Timeout for connection is 90 sec and after 120 sec

controller starts the next attempt. During the time the IL-NT GPRS is trying to send an active call type,

incoming calls are blocked.

Setpoint group

Act. Calls/SMS

Related FW

2.5.0

Range [units]

OFF, ON [-]

Default value

Step

Comm object

8482

Related applications

Description

Set this setpoint to YES if you want to get messages when a yellow (warning) alarm occurs.

Note:

The target address (cellular network phone number or e-mail address) must be set correctly to the

setpoint(s) TelNo/Addr Ch1 resp.

TelNo/Addr Ch1, 2 (page 182)

Yel Alarm Msg

back to List of setpoints

Содержание InteliDrive FLX LITE





































































































































































































































Результаты поиска

Содержание InteliDrive FLX LITE

Отзывы:

Похожие инструкции для InteliDrive FLX LITE

Бренды по названию

Популярные бренды

ComAp InteliDrive FLX LITE, Руководство пользователя

Результаты поиска

Содержание InteliDrive FLX LITE

Отзывы:

Похожие инструкции для InteliDrive FLX LITE

Бренды по названию

Популярные бренды