ComAp IM-NT Скачать руководство пользователя

Страница: 139 / 328

InteliMains

, SW version 3.0

InteliMains-NT-BTB-3.0-Reference Guide.pdf,

©ComAp – June 2013

139

Range [units]

0.0 .. 60.0 [s]

Related FW

3.0

Force value
possible

YES

Description

This setpoint adjusts the delay after the binary input

Force block 3

has been

deactivated, when the alarms configured as

Force block #3

are started to be

evaluated.

12.2.4.8

Setpoint: ResetActAlarms

Group

ComProtSetting

Range [units]

[-]

Related FW

3.0

Description

DISABLED

Pressing of the fault reset button (at any terminal or
external button) resets only

inactive

alarms. Active

alarms remain in the alarmlist unchanged and must be
reset again when they become inactive.

ENABLED

Pressing of the fault reset button (at any terminal or
external button) resets

all

alarms that are currently

present in the alarm list. Inactive alarms disappear from
the alarm list immediately, active alarms are changed to
"confirmed" state and disappear when the alarm condition
disappear or the alarm starts to be blocked.

OTE

ENABLED position corresponds to the method how the IG-classic and IS-
classic controllers handled the alarms.

12.2.5 Group: Analog protect

12.2.5.1

Setpoint: Batt >V

Group

Analog protect

Range [units]

8.0 .. 40.0 [V]

Содержание IM-NT









































































































































































































































































































































Результаты поиска

Содержание IM-NT

Отзывы:

Похожие инструкции для IM-NT

Бренды по названию

Популярные бренды

ComAp IM-NT, Справочное руководство

Результаты поиска

Содержание IM-NT

Отзывы:

Похожие инструкции для IM-NT

Бренды по названию

Популярные бренды