ComAp IM-NT Скачать руководство пользователя | Manualshive

Страница: 127 / 328

background image

InteliMains

NT

, SW version 3.0

InteliMains-NT-BTB-3.0-Reference Guide.pdf,

©ComAp – June 2013

127

Range [units]

[-]

Related FW

3.0

Description

This setpoint can be used to add extra AT commands at the end of the
initialization sequence of the modem connected to the COM2 port. The
command can be entered with as well as without the "AT" prefix, are
separated with semicolon and maximal length is 31 characters.

The setpoint can't be modified via the IG-NT built-in terminal.

Using a modem at the COM2 port is not supported since the hardware
version 2.0. For modem use the COM1 port instead.

12.2.3.10

Setpoint: RS485(1) conv.

Group

Comms settings

Range [units]

DISABLED, ENABLED [-]

Related FW

3.0

Description

This setpoint selects function of the built-in RS485(1) converter.

ENABLED

The communication port COM1 is redirected to the
integrated RS485(1) converter. The RS232(1) connector
has no function and the external display interface is not
available.

DISABLED

The communication port COM1 is present at the RS232(1)
connector and the RS485(1) connector is used for the
external display interface.

N

OTE

:

The redirection is applied only for DIRECT, MODBUS and ECU-LINK modes.
See the setpoint

RS232(1) mode

N

OTE

:

This setpoint must be set to

DISABLED

at controllers that do not have

internal display. i.e. InteliVision-5 or InteliVision-8 is connected to the
RS485(1) terminals.

«
...
125
126
127
128
129
...
»

Содержание IM-NT









































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IM-NT

Бренд: Samsung Страницы: 32

VLT AQUA Drive FC 202

Бренд: Danfoss Страницы: 124

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 8

Бренд: Danfoss Страницы: 114

ECL Comfort 300

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 16

Бренд: Danfoss Страницы: 24

Бренд: Danfoss Страницы: 8

ECL Comfort 296

Бренд: Danfoss Страницы: 159

VLT AutomationDrive FC 301

Бренд: Danfoss Страницы: 78

Бренд: Danfoss Страницы: 20

ECL Comfort 210

Бренд: Danfoss Страницы: 12

ECL Comfort 110

Бренд: Danfoss Страницы: 8

ECL Comfort 100M

Бренд: Danfoss Страницы: 21

Бренд: Danfoss Страницы: 16

Бренд: Danfoss Страницы: 64

Бренд: Warren Controls Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды