29
ATTENTION:
during this operation, check there are no people
or objects near the machine.
ATTENTION:
the ramp gradient must not be such as to cause
damage to the machine as it goes up.
10. Once the machine is on the transport vehicle, engage the
parking brake by moving the parking brake lever (6) in the
direction shown by the arrow (
Fig.9
).
ATTENTION:
the indicator light (7) relating to the engaged
parking brake will be activated on the control panel (
Fig.7
).
11.
Bring the main switch (1) to "0", turning the key (2) a quarter turn
to the right (
Fig.10
). Remove the key from the instrument panel.
12. Get off the machine.
ATTENTION:
do not position your foot above the brush head
while the machine is coming down the ramp.
13. Grip the handle (9) at the side of the seat (
Fig.11
), and raise the
seat mounting plate to the maintenance position (
Fig.12
).
14. Disconnect the battery connector (10) from the main system
connector (11) of the machine (
Fig.13
).
15. Grip the handle (9) and lower the seat mounting plate to the
working position (
Fig.14
).
ATTENTION:
secure the device according to the directives in
force in the country of use, so that it cannot slide or tip over.
TRANSPORTING THE MACHINE (G VERSIONS)
To transport the machine safely, proceed as follows:
ATTENTION:
before starting any task, make sure the current
regulations concerning the safe transport of dangerous
substances are scrupulously observed.
1. Make sure the solution and recovery tanks are empty. If this is
not the case, empty them (read “
” and “
2. Sit on the driver’s seat.
ATTENTION:
when it is running, the endothermic engine
produces carbon monoxide which is a toxic gas. Don't switch
the engine on in closed places.
3. Bring the command lever for the endothermic engine (1) rpm to
about 1/3 of its stroke - shift the lever in the direction shown by
the arrow (
Fig.1
).
4. Move the fuel selector command lever (2) in the direction shown
by the arrow to select “GASOLINE” (
Fig.2
).
5. Insert the key (3) in the main switch (4) on the control panel.
Bring the main switch (3) to "I", turning the key a quarter turn to
the right (
Fig.3
).
ATTENTION:
wait a few seconds before turning the key to
“START” (again to the right), and hold it until the engine starts
up. you can now release the key.
ATTENTION:
do not use the starter for more than 5 seconds
at a time. If the engine does not start up, release the key and
wait for 10 seconds before making a new attempt. If the
electric starter is used for more than 5 seconds at a time, it
overheats and may become damaged.
ATTENTION:
to cold-start the engine, bring the air command
lever (5) to “CLOSED”, moving it in the direction shown by
the arrow (
Fig.4
).
11
12
9
13
14
10
6
10
11
5
1
2
9
7
8
5
6
5
6
7
8
Содержание ULTRA 120 B-G
