COMAC C100 ESSENTIAL Series, Руководство по эксплуатации и обслуживанию

Страница: 28 / 40

CLEANING THE SQUEEGEE BODY
The careful cleaning of the whole vacuum unit ensures better drying and cleaning of the floor as well as a longer vacuum motor life. To carry out the
cleaning of the squeegee body, proceed as follows:
1. Extract the vacuum hose (1) from the vacuum nozzle on the squeegee body ( Fig.1 ).
2. Completely unscrew the knobs (2) in the squeegee body's pre-assembly ( Fig.2 ).
3. Remove the squeegee body from the slits in the squeegee connector ( Fig.3 ).
4. Thoroughly clean the squeegee body vacuum chamber (3) with a jet of water, and then with a damp cloth ( Fig.4 ).
5. Thoroughly clean the squeegee body rear rubber blade (4) with a jet of water, and then with a damp cloth ( Fig.5 ).
6. Thoroughly clean the squeegee body front rubber blade (5) with a jet of water, and then with a damp cloth ( Fig.6 ).
7. Use a jet of water and then a damp cloth to thoroughly clean the vacuum nozzle (6) ( Fig.6 ).
8. If you wish to use the tank cleaning kit to clean the squeegee body, see “TANK CLEANING KIT (OPTIONAL)”.
9. Proceed in the opposite order to reassemble all the parts.
N.B. : Check the wear of the rear rubber blade (4) on the squeegee body; if the edge of the rubber in contact with the floor is worn, replace
it. Refer to
"
REPLACING THE SQUEEGEE BODY RUBBER BLADES ".
N.B. : Check the wear of the front rubber blade (5) on the squeegee body; if the edge of the rubber in contact with the floor is worn, replace
it. Refer to
"
REPLACING THE SQUEEGEE BODY RUBBER BLADES ".
6 4 5
4
5
6
2 3 1
1 2 3
CLEANING THE SCRUBBING BRUSH HEAD LATERAL SPLASH GUARD RUBBER BLADES
Careful cleaning of the side splash guard rubber blades of the scrubbing brush head guarantees better cleaning of the floor. To clean the side
splash guard rubber blades, proceed as follows:
1. Go to the left hand side of the machine, and with the brush head raised up from the floor, remove the side splash guard casing from the brush
head ( Fig.2 ).
N.B. : Before removing the splash guard casing, turn the fixing anchors (1) on the brush head body to the maintenance position ( Fig.1 ).
2. Use a jet of water and then a damp cloth to thoroughly clean the side splash guard rubber blade (2) (
Fig.3
)
3. Reassemble all parts and repeat the operations described for the right side casing.
1 3 2
1 2
CLEANING THE SCRUBBING BRUSH HEAD BODY BRUSHES
Careful cleaning of the brush guarantees better cleaning of the floor as well as a longer lifespan of the gear motor present in the brush head body.
To clean the brushes, proceed as follows
1. Go to the left hand side of the machine, and with the brush head raised up from the floor, remove the side splash guard casing from the brush
head ( Fig.2 ).
N.B.
: Before removing the splash guard casing, turn the fixing anchors (1) on the brush head body to the maintenance position (
Fig.1
).
2. Press the brush locking pin (2) ( Fig.3 ).
3. Keeping the pin (2) pressed, turn the brush clockwise until it is released ( Fig.4 ).
4. Turn until the button is pushed towards the outside of the coupling spring and is locked into place.
5. Clean the brush under a stream of running water to remove any impurities from its bristles. Check the wear status of the bristles and replace
the brushes if they are excessively consumed (the bristles' protrusion must not be less than 10 mm; this distance is indicated on the brush by
the yellow band). For replacing the brushes, refer to “ FITTING THE SCRUBBING BRUSH HEAD BRUSHES ”.
6. After checking to make sure that the brush is clean, reassemble it and move on to the one on the right hand side.
N.B. : it is advisable to invert the position of the right and left-hand brushes every day.
28