COMAC ANTEA 50 B, Руководство по эксплуатации и обслуживанию

Страница: 38 / 44

22. After adjusting the amount of water in the dosing circuit, press the button (15) for adjusting the
detergent percentage supplied by the dosing system ( Fig. 23 ).
N.B. : Set the percentage of detergent present in the dosing system to the maximum value by
pressing the button (15) until the “DETERGENT PERCENTAGE ADJUSTMENT” symbol is
completely filled (Fig. 24 ).
23. Check that the potentiometer knob (16) is set to minimum, otherwise turn it completely counter-
clockwise ( Fig. 25 ).
N.B.
: the device will not start to move (either forward or backward) if the potentiometer adjustment
knob (16) is set to minimum.
24. Lower the brush head body, press the “BRUSH HEAD CONTROL” button (12) on the control panel
( Fig. 26 ).
25. Lower the squeegee unit using the lever (18) on the back of the appliance ( Fig. 27 ).
26. When the dead man's lever (19) is activated ( Fig. 28 ), the brush head gearmotor and the vacuum
motor will enter into function. At the same time, the solenoid valve and dosing system will begin
supplying the detergent solution to the brush.
27. Wait a few minutes, normally 2 – 4 minutes, to allow the dosing system to be washed.
N.B. : the machine will dispense solution during this operation.
28. Completely empty the solution tank and the detergent canister (read the paragraph “ EMPTYING
THE SOLUTION TANK” and the paragraph “CLEANING THE DETERGENT CANISTER (VERSIONS
WITH CDS) ”).
22
15
23
24
11
12
25 26
13
27
14
28
CLEANING THE RECOVERY TANK
To clean the recovery tank, proceed as follows:
1. Take the device to the dedicated maintenance area.
2. Take all necessary steps to ensure that the device is in a safe condition (see “ MACHINE SAFETY ”).
CAUTION : users are advised to always wear protective gloves, to avoid the risk of serious injury
to hands.
3. Remove the drainage hose of the recovery tank from the clamps; it is located at the rear of the
machine ( Fig. 1 ).
4. Bend the end of the drainage tube, so as to create a choke and prevent the content from coming out
( Fig. 2 ), put the tube on the discharge surface and gradually release the tube.
N.B.
: the place designated for this operation must comply with current environmental protection
regulations.
5. Grip the handle (1) on the back of the recovery tank cover and remove it ( Fig. 3 ).
6. With the recovery tank empty, rotate the recovery tank cover support (2). The optional support is
positioned on the left side of the appliance (
Fig. 4
).
7. Insert the clamp (3) of the recovery tank cover in the slot (4) on the recovery tank cover support
( Fig. 5 ).
2 1 3
1
4
2
5
4
3
8. Rinse the inside with a jet of water, if necessary use a spatula to remove the sludge that has
accumulated at the bottom of the tank.
9. Repeat the operations in reverse order to reassemble all the parts.
To clean the recovery tank filter-float with the spray gun, for versions with the SST system, proceed as
follows:
1. Take the device to the dedicated maintenance area.
2. Lift the brush head body and press the “BRUSH HEAD CONTROL” button (1) on the control panel
( Fig. 1 ).
3. Raise the squeegee unit and turn the squeegee control lever (2) in the direction of the arrow in
( Fig. 2 ). The lever is located on the back of the device.
4. Remove the drainage hose of the recovery tank (3) from the clamps; it is located at the rear of the
machine ( Fig. 3 ).
5. Bend the end of the drainage tube, so as to create a choke and prevent the content from coming out
(
Fig. 4
), put the tube on the discharge surface and gradually release the tube.
N.B. : the place designated for this operation must comply with current environmental protection
regulations.
6. Grip the handle (4) on the back of the recovery tank cover and remove it ( Fig. 5 ).
7. Rotate the recovery tank cover support (5). The optional support is positioned on the left side of the
appliance ( Fig. 6 ).
4 6 5
4
5
8. Insert the clamp (6) of the recovery tank cover in the slot (7) in the recovery tank cover support
( Fig. 7 ).
9. Remove the spray gun kit from the storage compartment ( Fig. 8 ).
10. Connect the male quick-coupler (8) on the spiral hose (9) to the female quick-coupler (10) on the
front of the appliance ( Fig. 9 ).
11. Connect the male quick-coupler (11) on spray gun (12) to the female quick-coupler (13) on the spiral
hose (9) ( Fig. 10 ).
12. Activate the spray gun kit by pressing the button (14) on the steering column ( Fig. 11 ).
CAUTION : when using the optional tank cleaning kit, you are advised to always wear goggles to
avoid any risk of serious injury to your eyes.
N.B. : Before activating the optional tank cleaning kit, check the level indicator (15) to see how
much solution there is in the solution tank ( Fig. 12 ).
13. Start the delivery of detergent jet by pressing the lever (16) on the spray gun ( Fig. 13 ).
N.B.
: To adjust the solution jet coming out of the spray gun
turn the knob (17) on the accessory
itself ( Fig. 14 ).
14. Rinse the inside with a jet of water, if necessary use a spatula to remove the sludge that has
accumulated at the bottom of the tank.
15. Repeat the operations in reverse order to reassemble all the parts.
3
1
1
2
3
2
8 7
7
6
9
9
8
10
10 11
15
12
13 14
11
12
16
17
13 14
38