manualshive.com logo in svg

Columbia CEG E Series, Инструкция по установке, эксплуатации и обслуживанию, Страница: 6 / 32

Поделиться
Скачать
Columbia CEG E Series Скачать руководство пользователя страница 6

6

LOCATING THE BOILER

Locating the Boiler

1. 

Select level location as centralized with piping system, 

and as near chimney as possible.

2. 

Place crated boiler at selected location. Remove all 

crate material. Please recycle responsibly.

WARNING

Fire hazard. Do not install boiler on combustible 

fl

 ooring or carpeting. Failure to follow these 

instructions could result in death or serious injury.

!

   

3. 

Do not install boiler on carpeting. For installation 

on non-combustible fl oors only.

 For installation on 

combustible 

fl

 ooring, special base must be used. (See 

Replacement Parts Manual.) 

4. 

Use metal shims under boiler base legs for 

fi

 nal leveling 

if needed.

5. 

Install boiler in location that permits satisfactory 

combustion of gas, proper venting, and maintenance 

of ambient temperature at safe limits under normal 

conditions of use. Boiler location should not interfere 

with proper circulation of air. Introduce outside air 

if normal in

fi

 ltration does not provide necessary 

air. “Fresh Air for Combustion” on page 12 .

6. 

Notify owner to keep air passages free of obstruction. 

Ventilating and combustion air must enter boiler room 

without restrictions.

 Table 3 -

Minimum Clearance Dimensions

Top

6"

Rear

6"

Control Side

7"

Opposite Side

6"

Front

Alcove

Flue/Vent 

Connector

6"

Near Boiler Piping

1/2"

7. 

Install boiler so automatic gas ignition system 

components are protected from water (dripping, 

spraying, rain, etc.) during appliance operation and 

service.

Draft Hood Installation

WARNING

Asphyxiation, carbon monoxide hazard. Failure to 

follow these instructions could result in improper 

combustion and possible leakage of combustion 

products into the living space.

!

   

Follow directions given in Figure 3. Attach draft diverter, 

and blocked vent switch. Mount vent damper. See 

"Connecting Vent Damper and Vent Connector" page 13. 

See Wiring Diagrams pages 26 and 27.

7” 

 (178mm)

6” (152mm)

Boiler

Rear

Front

Control Side

Opposite Side

ALCOVE

6” 

(152mm)

 Figure 2 - Minimum Clearances To Combustible 

Construction

 Figure 3 - Draft Hood Installation

1. 

Slide draft hood over 

fl

 ue collector.

2. 

Through holes in jacket top, secure with 1 or 2 screws, 

based on boiler size.

Draft 

Hood

Screw

View from top 

of boiler

Top and side panels not shown for clarity.

Содержание CEG E Series

































Отзывы:

Нет отзывов