background image

8

SECTION 3:  TRACTOR SET-UP

NOTE: 

This owner’s manual covers various models of

lawn tractors. The units illustrated may vary slightly
from your unit. Follow only those instructions which
pertain to your model lawn tractor.

Attaching the Battery Cables

NOTE: 

The positive battery terminal is marked Pos.

(+). The negative battery terminal is marked Neg. (–).

The positive cable (heavy red wire) is secured to 
the positive battery terminal (+) with a hex bolt and 
hex nut at the factory. Make certain that the rubber 
boot covers the terminal to help protect it from 
corrosion.

Remove the hex bolt and wing nut from the 
negative cable. 

Remove the black plastic cover, if present, from the 
negative battery terminal and attach the negative 
cable (heavy black wire) to the negative battery 
terminal (–) with the bolt and wing nut.

Make certain the retainer rod is in position over the 
battery, securing it in place. See Figure 1.

Figure 1

NOTE: 

If the battery is put into service after the date

shown on top of battery, charge the battery as
instructed

 in the SERVICE section of this manual prior

to operating the tractor.

Gas and Oil Fill-up

The gasoline tank is located under the hood and has a 
capacity of either two or three gallons. Do not overfill. 

WARNING: 

Use extreme care when

handling gasoline. Gasoline is extremely
flammable and the vapors are explosive.
Never fuel machine indoors or while the
engine is hot or running. Extinguish
cigarettes, cigars, pipes, and other sources of
ignition.

Service the engine with gasoline and oil as instructed in 
the separate engine manual packed with your tractor. 
Read instructions carefully.

IMPORTANT:

 Your tractor is shipped with motor oil in the 

engine. However, you 

MUST 

check the oil level before 

operating. Be careful not to overfill.

Shipping Brace Removal

WARNING: 

Make sure the riding mower’s

engine is off, remove the ignition key, and set
the parking brake before removing the
shipping brace

.

Locate the shipping brace, if present, and 
accompanying warning tag found on the right side 
of the mower, between the discharge chute and the 
cutting deck. See Figure 2.

Figure 2

While holding the discharge chute with your left 
hand, remove the shipping brace with your right 
hand by grasping it between your thumb and index 
finger and rotating it clockwise.

WARNING: 

The shipping brace, used for

packaging purposes only, must be removed
and discarded before operating your riding
mower.

Rubber Boot

Hex Bolt

Wing Nut

Retainer Rod

Shipping Brace

Warning Tag

Содержание Automatic Lawn Tractor






























Отзывы: