Colop digital e-mark create Скачать руководство пользователя страница 37

Страница: 37 / 60

e-mark create marking device

Chapter 5 Operation

CODI Standard 1.0

37/60

Operating and Maintenance Manual

5.4 Automatic cleaning cycle

Print head cleaning is required for optimum device performance. This can be run automatically and manually.

Print head cleaning:

A print head cleaning cycle is automatically activated when the e-mark create is taken from the docking station. Ink

drops in picolitre range (depending on the downtime) are released when the device is raised. These are dispersed

as a thin mist in the air. This is necessary to ensure constant print quality. This process can also be found inside an

inkjet printer. Do not rotate the e-mark create directly after raising from the docking station. The automatic cleaning

cycle is run when the e-mark create is in a level position. No print head cleaning is completed for safety reasons if

the e-mark create is rotated more than 90°.

Do not touch the e-mark create print head. Do not place on or immediately above light surfaces or clothing

– ink

stains can be hard to wash out!

If ink gets into the print head rest pad, it can stick together. This may happen if the e-mark create has just been

removed from the docking station (print head cleaning is activated) and is returned to the docking station without

printing. Always print on a suitable surface after removing.

Fig. 24: Colour sample released by

automatic print head cleaning

Fig. 25: Do not direct towards eyes, face or skin. Light irritation possible

CAUTION!

Possible hazard from substances, slight eye and skin irritation from ink.

Do not direct the print head towards the eyes, face or skin. Do not open the ink

cartridge. Do not swallow! Keep ink cartridge out of the reach of children.

The print head and housing must always be placed in the docking station when not in use to prevent drying out.

The docking station contains a special pad with rubber lips to prevent drying out.

Содержание digital e-mark create





























































Результаты поиска

Содержание digital e-mark create

Отзывы:

Похожие инструкции для digital e-mark create

Бренды по названию

Популярные бренды

Colop digital e-mark create, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание digital e-mark create

Отзывы:

Похожие инструкции для digital e-mark create

Бренды по названию

Популярные бренды