PRI:
Uin=24VDC
lin=4A
SEC:
Uout=4x(24)VDC
Iout=4x1A
TEMP RANGE:-20°C-+50C
SIGNAL
OUTPUT
Learning
Switch
xxxxxx
6-7mm
0.5-2.5mm
2
CWL 2409 V1
24V INPUT
LEARNING SWITCH
TR2818 WiFi TO RF TRANSMITTER
Instructions / Instructions de câblage / Installationsanleitung
CWI 8080 V2
EN
SYNCING APP TO HOME / OFFICE WIRELESS NETWORK
7. Select
CONNECT WIFI LED CONTROLLER TO YOUR HOME NETWORK
.
Note – With IOS device, message “your cellphone has connected to Easylighting network
successfully” appears. Press Yes.
8. Wait for a full list of available WiFi networks to be displayed.
9. Select appropriate WiFi network and enter password if applicable.
10. (a) -
ANDROID
- Message “Configure successfully” appears. Wait for device to reconnect to
home network (may be up to 30 seconds). When reconnected, press OK.
(b) –
IOS
– Message “configure successfully” appears, then disappears.
Message “WiFi device is not found “ appears. Press OK.
Message “configure successfully” appears. Press OK.
Go to IOS device settings, select home wifi, then return to APP.
11. Press
ROOM
button.
12. Select
Zone 1
(labelled as bedroom).
If tick is top right corner, continue to step 13.
If tick is not in top right corner, press bedroom button.
13. Press
ROOM
button. A single colour wheel will appear.
Note – if 4 colour wheels appear, select the top left wheel.
14. On the C100924 controller, press the
LEARNING
switch (see C100924 diagram).
15. Within 5 seconds, turn the inner ring of the
COLOUR WHEEL
.
The LEDs will flash to indicate connection is successful.
16. Repeat steps 11-15 to set up additional zones (tick only the required room in step 12).
Zone names can be edited from
SETTINGS > EDIT ROOM INFO
.
There are two connection methods.
Sync App directly to the TR2818.
This method uses the WiFi signal from
the TR2818. When in use, access to the
internet is not possible without swapping
wireless networks.
Sync App via a home or office network.
This method uses the WiFi signal from the
home / office router. When in use, access to the
internet is possible without swapping wireless
networks.
FUNCTIONALITY
1. The colour wheel can be used to change the colour of the LEDs.
2. Alternatively, the buttons surrounding the colour wheel can be used for more precise control.
3. The
BRIGHTNESS
button allows control of the brightness.
4.
W
button allows control of the WHITE LED.
5.
RGB
button allows control of the RGB LEDs - moving the bars will activate control of the LEDs
by this method.
6. The
PLAY / PAUSE
button allows colour cycling. This button also allows light to music syncing,
either through internal phone music, or external device (using microphone).
7. There are 10 pre-set cycles. Press
PLAY
to select cycle 1, press
PAUSE
, press
PLAY
to move
onto cycle 2, etc.
The slide controls the colour cycle speed.
SAVING COLOURS TO ZONES
1. Select the colour or cycle required.
2. Press and hold S1 or S2 or S3, etc.
3. The connected lights will blink.
4. To recall a colour or cycle from a saved position, press on S1, or S2 or S3, etc.
To understand the installation, read these instructions and the power repeater instructions BEFORE commencing wiring.
Provide a 24V DC supply to the TR2818. A Collingwood 15W 24V DC driver is ideal. The
most convenient location for the TR2818 is often with the controllers and power repeaters,
as a mains supply will already be established there for the rest of the installation.
EN
t +44 (0) 1604 495 151 f +44 (0) 1604 495 095
e [email protected] w collingwoodlighting.com
xxxxxx
6-7mm
0.5-2.5mm
2
Uin=24VDC
lin=0.3A(max)
RF Out=10dBm(max)
RF Frequency=869.5MHz
TEMP RANGE:-20°C-+50°C
Reset
Switch
CWL 2412 V1
15W
24V DC
Driver
240V AC, 50/60Hz
SYNC APP
1. Press and hold the ‘reset’ switch on the TR2818 for 5 seconds. After 5 seconds the LED
indicator lights will go off, the software will be reset and the ready LED will light.
2. Download
COLLINGWOODRGBW
from appropriate place.
3. Go to the wireless settings on your smart device.
4. Select
EASYCOLOUR 23xxxx
.
5. Go to the
COLLINGWOODRGBW
App.
6. Press
SETTINGS
button.
Go to (b) or (c) as required.
IOS or Android
TR2818
Router
TR2818
C100924
C100924
IOS or Android
(a)
(b)
1.
4.
3.
(a)
(b)
(c)
DIRECT TO TR2818
7. Select
USE DIRECT EASYLIGHTING CONNECTION WITH WIFI LED CONTROLLER
.
Note – With IOS device, message “your cellphone has connected to Easylighting network
successfully” appears. Press Yes.
8. Press
ROOM
button.
9. Select
Zone 1
(labelled as bedroom).
If tick is top right corner, continue to step 10.
If tick is not in top right corner, press bedroom button.
10. Press
ROOM
button. A single colour wheel will appear.
Note – if 4 colour wheels appear, select the top left wheel.
11. On the
C100924
controller, press the
LEARNING
switch (see C100924 diagram).
12. Within 5 seconds, turn the inner ring of the
COLOUR WHEEL
.
The LEDs will flash to indicate connection is successful.
13. Repeat steps 8-12 to set up additional zones (tick only the required room in step 9).
Zone names can be edited from
SETTINGS > EDIT ROOM INFO
.
Attach WiFi antenna (marked ANT1) to position ANT1 on the TR2818.
Attach RF Antenna (marked ANT2) to position ANT2 on the TR2818.
2.
Note: Antennas must be attached in the correct positions.
