Typical Cooling Screen
HEATING:
The unit will operate in heating mode to
maintain the set point temperature. There are two
selections in the Heating Mode – Heat Pump (ELE)
and GAS (gas furnace). (Heating only functions on air
conditioners with electric heat, heat pumps or vehicles
with an auxiliary source of heat, e.g. a gas furnace.)
A. Vehicles without a gas furnace
1.
Using the Mode button, scroll through the various
setting by repeatedly pressing the Mode button
until HEAT ELE is shown.
2.
Using the
UP
&
DOWN
buttons, select the
desired set point temperature.
3.
Press the
FAN
button to select either High or Low
Fan speed.
4.
Press the mode button twice to go to Auto Mode,
bypassing the HEAT GAS set up.
B. Vehicles with a gas furnace
1.
Repeat steps 1-3 above.
2.
Press the
MODE
button once and Heat GAS is
shown.
3.
Using the
UP
&
DOWN
buttons, select the
desired set point temperature.
4.
In HEAT GAS, the fan speed is selected
automatically; the user can not select the fan
speed.
5.
Press the
MODE
button to go to AUTO mode.
NOTE:
HEAT GAS should only be used if a gas furnace
is to be operated with the controller. In Gas heat mode,
Follow Me is automatically turned on. See description of
Follow Me below.
AUTO:
The unit will automatically heat and cool,
depending on the set point temperature. (Heating only
functions on air conditioners with electric heat, heat
pumps or vehicles with an auxiliary source of heat, e.g. a
gas furnace). Use the
UP
&
DOWN
buttons to select the
desired set point temperature. In the Auto mode, the fan
speed is selected automatically. To advance to the Dry
mode, press the
MODE
button.
DRY:
This mode is for dehumidification when the
vehicle is not in use. The unit will operate in the cooling
mode to provide dehumidification. Use the
UP
&
DOWN
buttons to select the desired set point temperature. If the
room temperature in is above the set point, the unit will
operate for 15 minutes and then turn off for 3 minutes. If
the room temperature is below the set point, the unit will
operate for 6 minutes and then turn off for 15 minutes.
In the Dry mode, the fan speed is selected automatically.
To advance to the Fan mode, press the
MODE
button.
FAN:
The indoor fan is run to circulate air, but the
compressor does not operate. In the Fan Mode, two fan
selections are available: High speed continuous or Low
speed continuous. Use the
FAN
button to select.
vii. FOLLOW ME
In normal operation a temperature sensor in the ceiling
assembly senses the temperature and controls the operation
of the Air Conditioner or Heat Pump. Follow Me switches this
control to a temperature sensor on the hand held controller.
To activate Follow Me, press the
Follow Me
button for 3
seconds and release. On or Off will flash on the screen.
Press the
Follow Me
button again to change the setting. In
Gas heat mode, Follow Me is automatically turned on.
viii. F/C
Selects whether the temperature is displayed in
Fahrenheit or Celsius. Press and hold the
F/C
button for
3 seconds and release. CEL or FAH will be displayed.
Press the
F/C
button again to change the selection.
ix. TIME AND DAY SET UP
1.
Press the
CLOCK
button and hold for 3 seconds.
2.
The hour and AM or PM will flash. To change the hour,
press the
UP
or
DOWN
button.
3.
To change the minute, press and release the
PROGRAM
button. To change the minute, press the
UP
or
DOWN
button.
4.
To change the day, press and release the
PROGRAM
button. To change the day, press the
UP
or
DOWN
button.
5.
Press the
CLOCK
button to return to the normal screen.
x. 7-DAY PROGRAMMING
The 7-day program schedule allows different set point
temperatures for different times of each day of the
week. The schedule includes four periods – Morning,
Day, Evening and Night- for each day of the week. Each
period has a start time, a set point temperature for Heat,
Cool and Auto modes. For 7-day programming:
1.
Press the
CLOCK
and
PROGRAM
buttons simultaneously
and hold for three seconds.
2.
The first selection is for the day of the week. Press the
UP
or
DOWN
button to select Monday (MON).
3.
Press the
PROGRAM
button to select the settings for the
Morning period. Press the
UP
or
DOWN
button to select
Morning.
4.
Press the
PROGRAM
button to select the hour for the
period to begin. Use the
UP
and
DOWN
button to select
the hour.
5.
Press the
PROGRAM
button to select the minute for the
period to begin. Use the
UP
and
DOWN
button to select
the minute.
6.
Press the
PROGRAM
button to select the set point
temperature for Cooling. Press the UP or DOWN button to
select the desired temperature.
7.
Press the
PROGRAM
button to select the set point
temperature for Heating. Press the UP or DOWN button
to select the desired temperature.
8.
Press the
PROGRAM
button to select the set point
temperature for Auto. Press the UP or DOWN button to
select the desired temperature.
9.
Repeat this procedure to select the start times and set
point temperatures for Monday Day, Monday Evening and
Monday Night.
10.
Repeat this procedure for the remaining days of the week.
If the unit is in the COOL, HEAT, or AUTO mode, it can
be run in either the Manual Run mode or the 7-Day
Preprogrammed Run mode. Pushing the
PROGRAM
button will toggle between the Manual Run mode and
7- Day Preprogrammed Run mode. While in the 7-Day
Preprogrammed Run mode, PROGRAM will appear at
the bottom of the screen. The set point temperatures
maybe changed by pushing the
UP
&
DOWN
buttons.
The manually set temperature will remain in effect until
the start of the next preprogrammed period. The 7-Day
preprogrammed mode is not available in the Fan only
or Dry mode.
10