S
T
IT
C
H
L
IN
E
To Attach Rainfly
continued
To Store
1.
All metal poles and stakes must to be placed in the storage
bag to prevent damage to the fabric items placed in the
carry case.
2.
Make sure tent is clean and dry before placing in carry case.
3.
Remove rainfly, spread out on floor of tent, then unzip
door & vents before taking tent down for storage.
4.
Neatly fold tent to width of pole storage bag, place on tent,
roll tightly, and place in carry case.
5.
Store in a clean, dry area.
12/07
7.
Assemble the interlocking, shock-cord-
ed back awning pole, with metal
tips on the angled end pieces.
8.
Insert back awning pole through
sleeve in rainfly awning at back of tent
as shown. (Fig. 6)
9.
Insert metal tip, on back awning pole,
into metal grommet in upper corner.
(Fig. 6 & 6A)
10.
Go to opposite end of back awning
pole and gradually apply pressure to the
pole to form an arch. Insert the metal
tip on the awning pole into the metal
grommet. (Fig. 6)
11.
Locate all hook & loop fasteners on
seams on underside of rainflay and
wrap around black main poles to
secure. (Fig. 7A)
12.
Tie guylines through loops on web
straps on the rainfly. (Fig. 7 & 7B)
13.
Stretch guylines until taut, then
secure with stakes. (Fig. 7C)
Things You Should Know:
•
Under certain conditions (cold weather, high humidity, etc.) condensa-
tion will form on the inside of your tent. Condensation is caused by
water vapor from your breath, perspiration, or any wet clothing inside
the tent. It is NOT LEAKAGE through the tent fabric. It can be minimized
by removing wet clothing from your tent and by providing good ventila-
tion through the tent.
•
Never store tent, even for a short period of time, without drying it
thoroughly and brushing off caked dirt. Do not pack stakes or poles
inside your tent. Use a separate storage bag.
•
STAKES SHOULD BE REMOVED BY PULLING ON THE STAKE ITSELF.
NEVER PULL ON THE TENT TO REMOVE STAKE.
•
TENT POLES SHOULD NOT BE LEFT TELESCOPED TOGETHER
DURING STORAGE.
•
Do not leave your tent set-up for weeks at a time. Be aware that exposure
to ultraviolet rays from the sun can seriously damage material and/or
cause it to become discolored.
WARNING: Keep all flame and heat sources away
from this tent fabric.
This tent meets the flammability requirements of CPAI-84. The
fabric may burn if left in continuous contact with any flame source.
The application of any foreign substance to the tent fabric may
render the flame-resistant properties ineffective.
Electrical Cord Access
1.
Unzip access panel in the lower
left corner of tent and bring in
electrical cord. Use only UL approved
cords that are rated for outdoor
usage. (Fig. 10)
Fig. 10
Fig. 7
Cooler Access
The smaller zippered opening at the
rear of the tent is designed for added
ventilation and easy access to your
beverage cooler.
1.
To use as a vent, unzip flap to
expose screen. (Fig.8)
2.
To use as a cooler access, unzip
other flap to make an avenue to
bring beverages into the tent.
(Fig.9)
Fig. 8
Fig. 9
7A
Black
Main
Pole
7B
Back Window
Back Window
Vent of Tent
Vent of Tent
6A
Front Door &
Vestibule of Tent
Back Awning &
Window Vent
of Tent
Side View of Tent
Grommet
Back
Awning Pole
Sleeve in Rainfly
Awning
Back Awning
Pole
7B
Fig. 6
Underside
of Rainfly
7C
The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219
1-800-835-3278 • www.coleman.com
Sunbeam Corporation (Canada) Limited
DBA Jarden Consumer Solutions
20B Hereford Street • Brampton, ON L6Y 0M1
1 800 387-6161 • www.colemancanada.ca
FABRIQUÉE EN CHINE • IMPRIMÉ EN CHINE
© 2007 The Coleman Company, Inc.
Coleman
®
et
sont des marques déposées de The Coleman Company, Inc.
