Coinco MAG50B Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 36

Coinco MAG50B Скачать руководство пользователя страница 20

20

SECTION 4: MAINTENANCE

MAG50 CLEANING PROCEDURE

FOR SALT WATER POLLUTED

UNITS

NOTE:

Petroleum-based cleaners and freon-based

propellants can damage plastic and some electronic

components. Scouring pads and stiff brushes may harm

the protective coating on the circuit boards and can mar

the plastic. These items should never be used when

cleaning the MAG bill acceptor.

Procedure

1. Remove power from the bill acceptor.

2. Remove the bill acceptor from the vending machine.

3. Open the bill box lid and verify that the stacker plate

is in the standby/home position. If it is not in the

home position, apply power and observe that the

stacker plate returns home.

4. Remove the bill box.

WARNING:

If moisture is present, allow the unit to dry

thoroughly before applying power to avoid possible

shock hazard. If the stacker plate does not return to the

home position, remove power and carefully remove the

bill box to avoid damaging the bill box and/or stacker

plate.

5. Remove the lower housing.

6. Remove the bottom cover from the lower housing.

7. Run hot water (110°-140°F) over the lower housing

from the top and bottom. Using a soft brush, gently

clean any salt residue. Use a soft, absorbent cloth to

clean residue off the lower housing. If the trans-

former gets wet, allow the unit to dry for 24 hours

before applying power.

8. Remove the front mask. Using hot water and a soft

brush, clean the front mask, upper sensor board and

main frame anti-pullback levers.

CAUTION:

The motors are not protected from water,

therefore the unit must be held in a manner that prevents

water from running over them.

9. Verify the anti-pullback levers move freely and that

the spring returns them to their extended position.

10. Allow the unit to dry thoroughly.

11. Clean the magnetic head using a swab and isopropyl

alcohol.

12. Replace the front mask.

13. Replace the lower housing cover.

14. Place the lower housing into the main frame.

15. Remount the bill box.

16. Apply power and insert bills to verify the unit is

functioning properly.

«
...
18
19
20
21
22
...
»

Содержание MAG50B





































Отзывы:

Нет отзывов