Congratulations on having purchased a
Coemar
product. You have assured yourself of a fixture of the highest quality, both in compo-
nentry and in the technology used. We renew our invitation to you to complete the service information on the previous page, to expe-
dite any request for service information or spares (in case of problems encountered either during, or subsequent to, installation). This
information will assist in providing prompt and accurate advice from your
Coemar
service centre..
Following the instructions and procedures outlined in this manual will ensure the maximum efficiency of this product for years to come.
1.1. Packaging
Open the packaging and ensure that no part of the equipment has suffered damage in transit. In case of damage to the equipment,
contact your carrier immediately by telephone or fax, following this with formal notification in writing.
Packing list
Ensure the packaging contains:
1 Pin Lite LED
1 Instruction manual
1.2. Transportation
The
Pin Lite LED
should be transported in either its original packaging or in an appropriate flight case.
2.1. Important safety information
Fire prevention:
1.
Never locate the fixture on a flammable surface.
2.
Minimum distance from flammable materials: 0.5 m.
3.
Minimum distance from the closest illuminable surface: 0,5 m.
4.
Replace any blown or damaged fuses only with those of identical values. Refer to the schematic diagram if there is any doubt.
5.
Connect the projector to mains power via a thermal magnetic circuit breaker.
Prevention against electric shock:
1.
High voltage is present in the internal of the unit. Isolate the projector from mains supply prior to performing any function which
involves touching the internal of the unit.
2.
For mains connection, adhere strictly to the guidelines outlined in this manual.
3.
The level of technology inherent in the
Pin Lite LED
requires the use of specialised personnel for all service applications; refer all work
to your authorised
Coemar
service centre.
4.
A good earth connection is essential for proper functioning of the projector. Never operate the unit without proper earth connection.
5.
The mains cable should not come into contact with other cabling.
6.
Never handle the unit with wet hands or in a damp environment.
Safety:
1.
The projector should always be installed with bolts, clamps, and other fixings which are suitably rated to support the weight of the unit.
2.
Always use a secondary safety chain of a suitable rating to sustain the weight of the unit in case of the failure of the primary fixing point.
3.
Never install the fixture in an enclosed area lacking sufficient air flow; the ambient temperature should not exceed 35°C.
4.
The external surface of the unit, at various points, may exceed 80°C. Never handle the unit until at least 10 minutes have elapsed
since the unit was turned off..
Protection rating of the body against liquids and solids:
1.
The standard version of the fixture is classified ordinary apparatus; its protection grade against penetration by external agents,solid or
liquid, is
IP 20
2.
The IP version of the projector has an
IP 65
protection rating; this indicates that it is protected against dust and significant showers
of water. This protection rating allows the fixture to be installed in an exposed location in inclement weather.
2.2. Warranty conditions
1.
The fixture is guaranteed for a period of 12 months against manufacturing faults and faulty materials.
2.
Faults due to incorrect operation or operation in an inappropriate manner are not covered by the warranty.
3.
The warranty is immediately void if the fixture has been operated or serviced by unqualified or unauthorised personnel.
4.
The warranty does not include fixture replacement.
5.
The model and serial numbers must be supplied for any warranty claims or advice from our authorised service personnel.
2.3. Certification
1.
The fixture satisfies the essential requirements of the directive EMC 89/336/EEC, 93/68/EEC, BT73/23/EEC.
2.
The fixture is in accordance with the standard EN 50419 (RoHS) and satisfies the requirements of the directive 2002/96/EC (WEEE).
2. General information
1. Packaging and transportation
English
4
Содержание PIN LITE LED
Страница 1: ......
