Code Alarm CA 6551 Скачать руководство пользователя | Manualshive

Страница: 16 / 60

background image

16

2010 Audiovox Electronics Corporation. All rights reserved.

Replacing Remote Control Batteries

1 Way 4 Button Remote Control - CA6551 / CA6551SST

The batteries inside each remote control should last approximately 1 year under
normal use. When the batteries become weak you will notice the remote control
range (the distance from the vehicle the remote control will work) deteriorate and the
small LED on the remote control will dim. To replace the remote control batteries:

1.

Remove 3 screws and disassemble the halves of the remote
control.

2.

Remove the old batteries, observing the +/- symbols on the
batteries and replace with new batteries.

3.

Reassemble the halves of the remote control and install the 3
screws.

4.

Test operation of the remote control.

NOTE:

The CA6551 uses 2 CR2016 batteries and the CA6551SST uses 1 CR2032.

2 Way LCD Remote Control - CA6551

The CR2450 battery inside the 2-way LCD remote control should last approximately 6
months under normal use. When the batteries become weak you will notice the
remote control range (the distance from the vehicle the remote control will work)
deteriorate and the BATTERY icon on the LCD remote control will show.

1.

Gently slide the battery cover off of the remote control.

2.

Remove the old CR2450 battery, observing the +/- symbols on the
battery, and replace with a new CR2450 battery.

3.

Gently slide the battery cover on to the back of the remote control.

4.

Test operation of the remote control.

2 Way LCD Remote Control - CA6551SST

The battery inside the 2 way LCD remote control is rechargeable, use the
supplied battery charger to charge the battery until the battery icon on the
LCD screen shows 3 bars indicating charging is complete. It is
recommended that the battery be fully charged before normal use.

«
...
14
15
16
17
18
...
»

Содержание CA 6551





























































Отзывы:

Нет отзывов

Похожие инструкции для CA 6551

Бренд: La Crosse Technology Страницы: 18

Бренд: First Alert Страницы: 5

Evolution-Advanced EV-DP

Бренд: Nittan Страницы: 7

Бренд: Honeywell Home Страницы: 4

Бренд: bolid Страницы: 2

Бренд: Fenwal Страницы: 14

CS-2014DP-TW2 Super Page

Бренд: CrimeStopper Страницы: 20

Бренд: CrimeStopper Страницы: 16

Бренд: CrimeStopper Страницы: 15

Бренд: Fire-Lite Alarms Страницы: 2

Titanus Micro-Sens

Бренд: WAGNER Страницы: 238

Бренд: La Crosse Страницы: 2

Бренд: La Crosse Страницы: 10

Бренд: Fire-Lite Страницы: 2

Бренд: Unitec Страницы: 34

Бренд: Viper Страницы: 60

Бренд: Shuoyu Technology Страницы: 6

Бренд: DEI Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды