Code Alarm CA 6151 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 34

background image

24

2010 Audiovox Electronics Corporation. All rights reserved.

Chirp Delete - User Accessible

System ARM/DISARM chirps can be toggled ON or OFF without entering the
programming feature banks.

1.

Turn the ignition ON then OFF.

2.

Press and release the valet/programming button 3 times. The system
will respond with 1 chirp for ON or 2 chirps for OFF.

NOTE: If the unit fails to learn tach rate due to an improper tach connection or a
poor tach source, the parking lights will not flash. To correct this situation, locate
and connect the PURPLE/WHITE wire to the proper tach signal, and then repeat
the tach learn routine.

Adjusting the Shock Sensor

1.

Increase sensitivity by turning the adjustment dial clockwise.

2.

Decrease sensitivity by turning the adjustment dial counter clockwise.

Testing the Shock Sensor

Arm the system and wait 6 seconds for the zone to stabilize, then firmly strike
the vehicles bumper.

Smart Tachless Mode

Smart Tachless Mode is available only if a tach signal has never been learned to
the system and when activated will automatically change the Tach Mode feature
in option programming to Tachless without the need to enter the feature
programming mode.

1.

Activate the remote start. The parking lights should begin flashing 7
times indicating no tach signal has been learned.

2.

Within the 7 flash time period, press and hold the

button.

3.

The system will chirp 1 time indicating the system is now in tachless
mode.

«
...
22
23
24
25
26
...
»

Содержание CA 6151



































Отзывы:

Нет отзывов

Похожие инструкции для CA 6151

Бренд: System Sensor Страницы: 4

POWERCLOCK IBT235W

Бренд: iHome Страницы: 11

Бренд: Radio Shack Страницы: 2

Бренд: LST Страницы: 1

Бренд: Argus Страницы: 4

Бренд: COP-USA Страницы: 21

Бренд: Carpal Страницы: 8

Бренд: Trevi Страницы: 6

Бренд: VESDA Страницы: 52

Бренд: Fenwal Страницы: 14

vesda LaserFOCUS VLF-500

Бренд: Xtralis Страницы: 61

PowerCode PC 6100

Бренд: Code Alarm Страницы: 12

Бренд: Code Alarm Страницы: 44

Бренд: Radio Shack Страницы: 4

Бренд: HumanTechnik Страницы: 40

Бренд: i-box Страницы: 48

Бренд: Clas Ohlson Страницы: 5

Бренд: Code Alarm Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды