background image

7

Directional module Flash Pattern 

PROBLEM

LED module not

operating when

powered.

POSSIBLE CAUSE

a.  Bad power/ground

   connection.

b.  Defective module.

SOLUTION

     

a.  Fix connection.

     

b.  Replace module

TROUBLESHOOTING GUIDE

Troubleshooting

All WingMan Rear Bars are thoroughly tested prior to shipment. However, should you encounter a problem during installation or 

during the life of the product, follow the guide below for information on repair and troubleshooting. Additional information may be 

obtained from the factory technical help line at 314-996-2800.

Note: 

LED modules must be replaced as a module. There are no user serviceable parts.

QUESTIONS

N/A

Parts List

 Reference Number             

                  Part Description   

                  Part Number

            1                                                    Outer Panel - Standard Single Level                        T15260

            2   

 

 

                      3Up Module                       *Contact Code 3, Inc for P/N

 

            3   

                                                6Up OPTIX Module                    *Contact Code 3, Inc for P/N 

 

            4                                                                      Mounting Brkt.                                         T15259

            5                                                          Chassis - Standard Single Level                         T15261

1

5

4

3

2

FIGURE 13

Содержание WingMan









Отзывы: