background image

920-0497-00 Rev. A

Page 2 of 8

            

Notes:

1.   Larger wires and tight connections will provide longer service life for components. For high current wires it is recommended   

      that terminal blocks or soldered connections be used with shrink tubing to protect the connections. Do not use insulation  

      displacement connectors (e.g., 3M Scotchlock type connectors)

2.   Route wiring using grommets and sealant when passing through compartment walls. Minimize the number of splices to 

      reduce voltage drop. High ambient temperatures (e.g., under-hood) will significantly reduce the current carrying capacity of 

      wires, fuses, and circuit breakers. All wiring should conform to the minimum wire size and other recommendations of the 

      manufacturer and be protected from moving parts and hot surfaces. Looms, grommets, cable ties, and similar installation 

      hardware should be used to anchor and protect all wiring.

3.   Fuses or circuit breakers should be located as close to the power takeoff points as possible and properly sized to protect the 

      wiring and devices.

4.   Particular attention should be paid to the location and method of making electrical connections and splices to protect these 

      points from corrosion and loss of conductivity.

5.   Ground termination should be only be made to substantial chassis components, preferably directly to the vehicle battery.

6.   Circuit breakers are very sensitive to high temperatures and will “false trip” when mounted in hot enviroments or operated 

      close to their capacity.

Wiring:

CCTC20-4

Important!

  Waterproof all connections whether inside or outside the vehicle by using sealant and wrapping 

with insulation tape. Wrap tape tightly, overlapping by one-half widths so there are no gaps.

A - Right Camera (Blue)

B - Left Camera (White)

C - Back Camera (Brown)

D - Front Camera (Green)

1 - AUX Audio Input

2 - Rec. Video Output (Green)

3 - Live Video Output (Yellow)

4 - Audio Output (White)

5 - Left Trigger (White)

6 - Right Trigger (Blue)

7 - Front Trigger (Green)

8 - Back Trigger (Brown)

9 - Split Trigger (Yellow)

10 - Ground (Black)

11 - Power (Red)

RCA:

12 - DVD Video Output (Yellow)

13 - DVD Audio Output (White)

14 - Black

22 Pin Male

22 Pin Female

4 Pin

Female

3A FUSE

A  B   C  D  1  2  3  4 5       6        7       8        9      10      11    12 13 14   

 

WIRING DEFINED

Содержание CC7000-QM









Отзывы: