Coda 33.0, Руководство по эксплуатации, Страница: 4 / 17

Stereo Amplifier Configuration
WARNING:
Please ensure that the power switch is turned OFF while you are connecting the
amplifier. Connecting or disconnecting cables while the amplifier is powered on could
cause damage to your speakers.
NOTE:
Ensure that the mode switch located between the input jacks on the rear of the
amplifier is set to the stereo position for normal operation. Bridged operation is explained on
page 7.
The diagram below shows the default connections necessary to operate the 33.0 as a
stereo amplifier. This is the simplest and most common mode of operation, and the quickest
way to get started. Once these connections are made you can turn the power switch on,
enable the bias from the front panel and start listening to your amplifier.
For simplicity this diagram shows an audio configuration using balanced interconnects. This
is the default input mode of the amplifier. Unbalanced operation requires that you set the
appropriate input mode as detailed on page 5.
INITIAL SETUP 3
LEFT SPEAKER RIGHT SPEAKER
PREAMPLIFIER
AMPLIFIER 33
! FOR CONTINUED PROTECTION AGAINST
SHOCK OR FIRE HAZARD,DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
AC LINE INPUT
SEE SERIAL T AG FOR
POWER REQUIREMENTS
~
UNBALANCED INPUT
RIGHT LEFT
COMPACT DISC
RIGHT LEFT
TUNER
RIGHT LEFT
VIDEO
RIGHT LEFT
MONITOR
RIGHT LEFT RIGHT LEFT
IN OUT PROCESSOR
RIGHT LEFT RIGHT LEFT
IN OUT VIDEO
RIGHT LEFT
UNBALANCED OUTPUT
RIGHT LEFT
T E C H N O L O G I E S I N C .
MODEL
SERIAL NUMBER
VOLTAGE REQUIREMENT
MANUFACTURED IN THE USA
HZ
POWER REQUIREMENT VA
FOR CONTINUED PROTECTION
AGAINST SHOCK OR FIRE:
1. REPLACE FUSE WITH SAME
TYPE AND RATING
2. DO NOT EXPOSE THIS UNIT
TO RAIN OR MOISTURE
BRIDGED
STEREO
DO NOT ALLOW AMPLIFIER OUTPUTS
TO COMMON BETWEEN CHANNELS,
OR CONTACT CHASSIS OR INPUT
GROUNDS, OR TO BE CONNECTED
TO ANY ACTIVE CURRENT SOURCE.
MAIN POWER
OFF ON
AC LINE FUSE CHART FUSE AND VOLTAGE SELECTOR
FUSE VALUE -SEE FUSE CHART
VOLTAGE SELECTION-
SEE OPERATION MANUAL
! NOTE
SEE SERIAL TAG FOR POWER
REQUIREMENTS, REMOVE POWER
CORD BEFORE CHANGING
FUSE OR LINE VOLTAGE
!
12
0
AC LINE INPUT
~
TO PREVENT ELECTRIC SHOCK, DO NOT
REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
CAUTION CAUTION
W W ARNING ARNING
!
LEFT CHANNEL
UNBALANCED
INPUTS
BALANCED
RIGHT CHANNEL
INPUTS
UNBALANCED
BALANCED
MODE
PUSH PUSH
VOLTAGE FUSE TYPE
100V
120V
220V
240V
12 AMP SLOW BLOW 5 x 20mm
6 AMP SLOW BLOW 5 x 20mm
DO NOT CONNECT AMPLIFIER OUTPUT
TERMINALS
TOGETHER. CONNECT
AMPLIFIER OUTPUT TERMINALS ONLY TO
SPEAKERS.
FOR CONTINUED PROTECTION AGAINST
SHOCK OR FIRE:
REPLACE FUSE WITH SAME TYPE AND
RATING. DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE
SEE SERIAL TAG FOR POWER REQUIREMENTS.
REMOVE POWER CORD BEFORE CHANGING FUSE OR LINE VOLTAGE.
AC LINE INPUT MAIN POWER FUSE / VOLTAGE SELECTOR
READ THE BRIDGING SECTION OF THE OPERATING MANUAL OR CONTACT YOUR CODA AUTHORIZED
DEALER TO SET THE BRIDGING SWITCHES
BRIDGED MODE
16 AMP
16 AMP
8 AMP
8 AMP
UNBALANCED
BRIDGED
INPUTS
INPUTS
BALANCED
BALANCED
INPUTS
UNBALANCED
PUSH PUSH
230