background image

Customer Assistance

Warranty

Introduction

17

Nothing 

Comes Close to a Cobra

®

Operation

16 English

Mode Functions

Operation

During channel scan (while receiving an incoming transmission), 
you can choose from the following:

a.

Press and hold the 

Talk

button to communicate on 

that channel. Your radio will remain on that channel 
and return to 

Standby 

mode.

b.

Press the 

Channel Up

or 

Channel Down

button to 

resume scanning channels.

If you press the 

Talk

button while scanning, but more than 

10 seconds after receiving a transmission, you will transmit 
on the channel on which you last received a transmission. 
This will return the radio to 

Standby

mode.

If you do not press any button within 10 seconds after 
receiving a scanned transmission, your radio will automatically
resume scanning channels. 

During channel scan (while not receiving a transmission), 
you can choose from the following:

a.

Press and hold the 

Talk

button to communicate on the

channel or channel/privacy code that was displayed before
you entered mode functions or the channel on which, during
scanning, you last received a transmission. This will then
return the radio to 

Standby 

mode.

b.

Press the 

Lock/Mode

button to proceed to set privacy 

code scan on the channel that was either displayed before 
you entered mode functions or on which, during channel
scanning, you last received a transmission (see page 18 
for further details).

c.

Press the 

Hi•Low/Enter

button to return to 

Standby 

mode

on the channel/privacy code that was displayed before you
entered mode functions or the channel on which, during
scanning, you last received a transmission.

Channel Scan

Your microTALK

®

radio can automatically scan channels.

To scan channels:

1.

Press the 

Lock/Mode

button until the 

Scan

icon and the channel numbers 

flash on the display.

2.

Press the 

Channel Up

or 

Channel Down

button to begin scanning channels.

The radio ignores specific privacy 
codes while scanning channels.

The 

Scan

icon will continue to be displayed 

when scan is 

on

. Your radio will continue to 

scan all channels and stop if an incoming
transmission is detected. Your radio will 
remain on that channel for 10 seconds. 

While setting channel scan, if you do not 
press any buttons for 15 seconds, your radio 
will automatically return to 

Standby 

mode on 

the channel or channel/privacy code displayed
before you entered mode functions.

Scanning Channels

Lock/Mode Button

Channel Buttons

Содержание microTALK PR5000DX




















Отзывы: