background image

Customer Assistance Warranty

Introduction

Operation

Battery Low

When battery power is low, the 

Battery Low

icon

will blink. Your batteries should be replaced or
recharged, if using rechargeable batteries.

Auto Battery Save

If there are no transmissions within 10 seconds,
the radio will automatically switch to 

Battery

Save 

mode and the 

Power Saver

icon will flash in

the display. This will not affect the radio’s ability
to receive incoming transmissions.

Communicating with Another Person

1.

Press and hold the 

Talk

button.

2.

With the microphone about two inches (5 cm)
from your mouth, speak in a normal voice.

3.

Release the 

Talk

button when you are 

finished talking and listen for a response.

You cannot receive incoming calls while 
pressing the 

Talk

button.

Both radios must be tuned to the 
same channel to communicate.

2

Using Your Radio

Operation

3

Quick Start

1.

Press and hold the 

Mode/Power

button 

to turn 

on

your radio.

2.

Press the 

Channel Up

or 

Channel Down

button to select a channel.

Both radios must be tuned to the same
channel/privacy code to communicate.

3.

Press and hold the 

Talk

button while 

speaking into the microphone.

4.

When finished talking, release the 

Talk

button and listen for a response.

Battery Low

Turning on Your microTALK

®

Radio

Press and hold the 

Mode/Power

button until you

hear a series of audible tones indicating the radio
is 

on

.

Your microTALK

®

radio is now in 

Standby 

mode,

ready to receive transmissions. The radio is
always in 

Standby 

mode except when the 

Talk

,

Call

or 

Mode/Power 

buttons are pressed.

Mode/Power

Talk Button

Battery Save Mode

Two Inches (5 cm) from

Mouth

To Select a Channel

With the radio 

on

, select any of the 22 channels by

pressing the 

Channel Up

or 

Channel Down

button. 

Both radios must be tuned to the 
same channel to communicate.

Channels 1 through 7 are shared with FRS/
GMRS. Channels 8 through 14 are FRS only.
Channels 15 through 22 are GMRS only.  

See 

page 14

for FRS/GMRS frequency

allocations and compatibility charts.

Channel Button

Channel Number

Nothing 

Comes Close to a Cobra

®

CXT240_MANL_OR_9509-PR260 WX vB  4/23/13  3:51 PM  Page 2

Содержание CXT240












Отзывы: