background image

 

1)  Installation Hints 

 
 

 

Make sure to clean the windshield and suction cup before installation. Use glass cleaner or 
rubbing alcohol.  

 

 

To attach the bracket to the windshield: 

1.  Make sure the locking lever is in the UP position 
2.  Lightly moisten the suction cup 
3.  Firmly hold the suction cup against the windshield 
4.  Push the locking lever.  

 

 

The 7700 PRO comes with a rubber bumper to protect your dash. If you let the unit rest on 
the dash, stick the rubber bumper onto the bottom of your unit.  

 

 

The GPS antenna is located at the top of the unit. During installation, arrange the mounting 
bracket so that it does not block the top of your unit.  

 
 

Using the Mounting Disc 

 
Note:  The adhesive pad is a separate piece.  The pad must first be stuck to the disk. 
 
1.  Find a flat part of the dash to attach the mounting disc. 
2.  Clean the dash with the enclosed alcohol pad. 
3.  Clean the DULL side of the mounting disk with the alcohol pad (not the shiny side). 
4.  Peel the backing from one side of the adhesive pad and then press the pad onto the DULL 

side of the mounting plate. 

5.  Peel the other backing from the adhesive pad and then press the mounting plate into position 

on the dash. 

6.  Clean both the mounting plate and the suction cup with the alcohol pad.  
7.  The mounting bracket (suction cup) can now be attached to the mounting plate. 
  

Once the plate is installed, it CANNOT be reused! 

 

NOTE: 

To create a secure mount, the plate uses a strong adhesive.  Please note that should you ever want 
to remove the plate, it might leave a mark on your dash.  So please decide in advance whether 
you really want to use it. 
 
 

<back to menu>

 

 
 

Содержание 7700 PRO



















































Отзывы: