mum sync for your particular camera will only be set in bright
conditions. The camera will also automatically select an
aperture. In this mode daylight fill flash is controlled by the camera.
APERTURE PRIORITY TTL (AV) MODE
It should be noted that the EOS system is so designed that in AV mod
a sync speed will not be set. The shutter speed selected by the earner
solely depends on the aperture selected and the amount of ambier
light present.
AV mode is useful when
is an important factor. Switcl
camera on and select AV mode (refer to
instruction book)
Select desired aperture via the camera's input dial and switch the
on. The camera will select a shutter speed between 30 seconds and tht
maximum sync speed.
NOTE:
If a small aperture is selected in low light conditions, the
will set a slow shutter speed. In this case either set a larger aperture o
ensure that your camera is mounted on a sturdy tripod to avoid
shake. If the maximum sync speed in the viewfinder blinks set a
aperture to avoid over-exposure.
SHUTTER PRIORITY TTL (TV) MODE
Like AV, TV mode reads ambient light and adjusts the aperture accord-
ingly. In low light conditions the camera will select a wide aperture - or
the aperture value may blink indicating that there is not enough light for
a
correctly exposed picture. The only method of correction is to select a
slower shutter speed.
This mode allows you to increase the background exposure for better
background detail and also creates a more natural lighting balance
between the subject and the background. Switch camera on and select
TV mode (refer to camera's instruction book). Select desired shutter
speed from the maximum sync to 30 seconds via the cameras input dial
and switch flash on. If the minimum aperture can be seen blinking in the
viewfinder select a faster shutter speed. If the maximum aperture blinks
select a slower one.
MANUAL TTL (M) MODE
Switch camera on and select M mode (refer to camera's instruction
book). Select desired shutter
from the maximum sync to 30
seconds & B, and desired aperture. The film speed selector/distance
scale (5) on the rear of the gun can be used as a guide to maximum
flash distances with most apertures.
NOTES:
The 700AF can also be used, when desired, with the PIC and
bar-code facilites offered by some EOS models. These modes will set
the camera up for a particular shooting condition and selects shutter
speed, aperture and film advance automatically. When flash is desired
with these simply select the command or bar-code desired, switch the
flash on and proceed, refering to your camera's instruction book and
the points mentioned in the above instructions.
Flash photography is not possible with the DEP mode offered by some
EOS models.
EXPOSURE CHECK
If the flash exposure is sufficient, the auto check lamp (9) will light up
briefly. If it fails to, check that you are within the maximum distance by
using the scale (5) on the rear of the flash. In AV and manual modes a
larger aperture can be selected allowing more light to strike the film.
MINOLTA DYNAX AF CAMERAS
Dynax
2xi, 3xi, SPxi, 5xi, 7xi, 9xi
The 700AF can be used with above cameras in
as Program TTL (P) mode, Aperture priority TTL (A) mode,
Shutter priority TTL (S) mode, and Manual TTL (M) mode, where the
user has control over both shutter speed and apertures.
NOTE:
The
has Program TTL (P) mode flash only, and the
program TTL (P) mode and Manual TTL (M) mode flash only.
PROGRAM TTL (P) MODE (Point and Shoot)
Switch camera on and select program (P) mode (refer to camera's
instruction book). This puts the camera
a "Point-and-Shoot" mode
and can be used for general flash photography. Switch flash on, once
charged a flash symbol will appear in the viewfinder and the flash ready
light (7) will glow. A shutter sync speed and aperture will be automati-
cally set by the camera. The exact sync speed set will depend on the
amount of available ambient light and the length of lens in use. Usually
the maximum sync for your particular camera will only be set in bright
conditions.
APERTURE PRIORITY TTL (A) MODE
This mode is useful when depth-of-field is an important factor. Switch
camera on and select A mode (refer to camera's instruction book).
Select desired aperture via tha camera's rocker or dial, and switch flash
on. The camera will select a sync speed depending on the Dynax
model. The scale (5) on the rear of the gun can be used to give a guide
to maximum shooting distances with most apertures.
SHUTTER PRIORITY TTL (S) MODE
Operates as per program TTL (P) mode. Shutter speed and aperture
are selected by the camera.
Donated to www.orphancameras.com
Содержание 700AF
Страница 1: ......
