Operation
Operation
Bluetooth
®
15
14
Bluetooth
Calls on a Bluetooth enabled cell phone can be
routed through the 29 WX NW BT speaker or
external speaker accessory.
C H 1 9
C H 9
N O R
RX/TX
WX
ANT
To Pair with a Cell Phone
With 29 WX NW BT power On, press and hold the BT Button
for six seconds to enter Standby mode. A tone will sound
and the BT LED will flash for one minute to confirm entry
to Standby.
From Standby, press and hold the BT Button for four
seconds to enter Pairing mode.
A.
First time pairing with a cell phone:
I. A tone will sound and the BT LED will flash rapidly
to confirm Pairing mode.
II. Follow the cell phone manufacturer's instruction
to enable its Bluetooth function and enter the PIN
(Personal Identification Number) 0000.
III. Successful pairing will be indicated by a tone and
brief flashing of the BT LED to confirm entry to
Connected mode. A pair record will also be established
for subsequent connections.
B.
Subsequent pairings with a cell phone:
I. Follow any cell phone manufacturer instructions,
if needed, to enable the Bluetooth function.
II. Successful pairing will be indicated by a tone
and brief flashing of the BT LED to confirm entry
to Connected mode.
1
2
To Answer Calls
Press and release the BT Button when the cell phone ring
is heard through the 29 WX NW BT speaker. The BT LED will
light steadily to indicate a call is in progress.
Speak into the 29 WX NW BT microphone. The CB function of
the unit and PTT Button will be disabled while a call is in
progress.
End the call by press and release of the BT Button.
A tone will sound and the BT LED will flash briefly.
To Initiate Calls
Dial a number according to the cell phone manufacturer’s
instructions. The key press and other tones will be heard
through the 29 WX NW BT speaker.
Press Send on the cell phone. The BT LED will light steadily
to indicate a call is in progress; and after a few seconds,
you will hear the ring tone for the number you dialed.
Once connected, speak into the 29 WX NW BT microphone.
End the call by press and release of the BT Button.
The BT LED will flash briefly.
Redial a number by press and hold of the BT Button for
two seconds. A tone will sound; and after a few seconds,
you will hear the ring tone for the number you dialed.
Note
If no further pairing steps are
taken, the unit will time-out
and return to Standby after
five minutes. During the pair-
ing process, press and
release the BT Button to can-
cel the pairing process.
1
2
3
1
2
3
4
5
To Enable or Disable Voice Dialing
If the paired cell phone supports voice dialing, press and
release the BT Button twice to toggle between enabling
and disabling this feature.
To Turn Off The Bluetooth Function
Press and hold the BT Button for six seconds to turn off
the Bluetooth function. Two short tones will sound and
the BT LED will turn Off and remain Off.
To Re-pair The 29 WX NW BT To The Cell Phone
If pairing is lost while the 29 WX NW BT power is On, press and hold
the BT Button for four seconds to re-pair with the cell phone.
If the 29 WX NW BT is turned Off, it will retain the Bluetooth address
and automatically re-pair with the last cell phone used when
it is turned back On.
BT LED
Indicator
BT Button
Note
For best audio quality while
using the Bluetooth feature,
place your cell phone at least
12 inches away from the
29 WX NW BT.
Note
When cell phone calls are in
progress using the Bluetooth
feature, the CB functions of
the unit are disabled.
Note
The external microphone can
be plugged into the rear of
the unit and clipped to a
pocket or lapel for hands-free
speech during calls.
When the external
microphone is plugged in,
the main microphone will not
pick up speech during calls
but will be fully functional
for CB operation.
29WXNWBT_MANL.qx:29WXNWBT_MANL.qx 1/7/09 4:26 PM Page 14
