Note
Dual Point Bluetooth:
For team drivers, two cell phones
can be paired, however; only one
phone can be used at a time.
Bluetooth®
Calls on a Bluetooth® enabled cell phone can be routed
through the 29 LX MAX speaker or external speaker
accessory.
23
22
Operation
Operation
To Pair with a Cell Phone
Press and hold the
BT Button
for six seconds to enter
Ready For Pairing
mode. A tone will sound to confirm
entry to pairing mode.
A.
First time pairing with a cell phone:
I. A tone will sound to confirm Pairing mode.
II. Follow the cell phone manufacturer’s instruction to
enable its
Bluetooth
function. Select 29 LX MAX from
the list of Bluetooth devices. Enter the PIN (Personal
Identification Number) 0000 if required.
Most smartphones no longer require a PIN entry.
Note
If no further pairing steps are
taken, the unit will time-out
and return to Standby after 90
seconds. During the pairing
process, press and release the
BT Button
or
DIM/ESC
to
cancel the pairing process.
Note
For Text-to-Speech conversion,
an app should be downloaded
to your cell phone.
Note
When cell phone calls are in
progress using the
Bluetooth
features, the CB functions of
the unit are disabled unless the
phone call is put on hold (see
page 27).
Setting Contrast Mode
Press the
Menu/Enter
knob and rotate
clockwise
to select
Set Contrast.
Rotate the
Menu/Enter
knob
clockwise
to increase
contrast,
counter-clockwise
to decrease contrast.
Press the
Menu/Enter
knob to save and exit and continue
settings or
DIM/ESC
to exit
Menu
mode.
SET CONTRAST
------
SAVE AND EXIT
MAX
III. Successful pairing will be indicated by
a tone to confirm entry to Connected
mode. A pair record will also be established for
subsequent connections.
B.
Subsequent pairings with a cell phone:
I. Follow the cell phone manufacturer’s instruction,
to enable it’s
Bluetooth
® function.
II.
Successful pairing will be indicated by a tone to
confirm entry to Connected mode.
SWR/CAL
NB/ANL
VOL
SQ
DYNAMIKE
RF GAIN
DELTA TUNE
T BACK
SWR
CAL
OFF
MIN
MIN
OFF
MAX
ESC
MEM SCAN
S/RF
M
EN
U PU
SH ENT
E R
SIG
RF
+30dB
1
1.5
2
3
CAL
3
5 7 9
SWR
TX
RX
NB/ANL
MEM WX !
ANL
S/RF
SWR
CAL
CH 9/
19
CB/WX
DIM
SCAN
READY FOR
PAIRING
PW 0000
MAX
BT Button
NW LIGHTING
CONTRAST
RADIO CHECK
1
2
3
To Answer Calls
Press and release the
BT Button
when the cell phone ring is
heard through the 29 LX MAX speaker.
Speak into the 29 LX MAX microphone. The CB function
of the unit and
PTT
Button will be disabled while a call
is in progress.
Press and release the
BT Button
to end the call.
A tone will sound.
To Initiate Calls
To initiate the phone’s voice assistant, if supported,
press and release the
BT Button
twice.
Dial a number according to the cell phone manufacturer’s
instructions. The key press and other tones will be heard
through the 29 LX MAX speaker.
Press Send on the cell phone, you will hear the ring
tone for the number you dialed on the CB speaker.
Once connected, speak into the microphone.
Press and release of the
BT Button
to end the call.
A tone will sound.
Press and hold the
BT Button
for two seconds to redial
a number. A tone will sound; and after a few seconds,
you will hear the ring tone for the number you dialed.
1
2
3
4
5
Note
When dialing a phone number
on your phone’s keypad, it is
recommended that you dial
when the vehicle is not in
motion.
Note
The external microphone (see
accessories on page 35) can be
plugged into the rear of the
unit and clipped to a pocket
or lapel for hands-free speech
during calls.
When the external microphone
is plugged in, the main
microphone will not pick up
speech during calls but will be
fully functional for CB operation.
AW-1210039-1B_29LX_MAX_MANL_REV_022021.indd 22-23
AW-1210039-1B_29LX_MAX_MANL_REV_022021.indd 22-23
2/24/21 2:55 PM
2/24/21 2:55 PM