COBHAM SAILOR 6080 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 44

COBHAM SAILOR 6080 Скачать руководство пользователя страница 6

iv

About the manual

Intended readers

This manual is an installation manual for the SAILOR 6080
Power Supply. It is important that you observe all safety
requirements listed in the beginning of this manual, and operate
the SAILOR 6080 Power Supply according to the instructions
and guidelines in this manual. All installation must be done by
qualified service personnel.

Manual overview

This manual has the following chapters:

•

Introduction

contains a description of the principle of

operation and uses and features of the power supply.

•

Installation

contains step-by-step guidelines how to install

the power supply as a stand-alone unit or in a combined
setup and describes the connectors.

•

Service and repair

contains information on support, how

to return units for repair and instructions how to exchange
the fuses.

• Appendices with

Technical specifications

, information

about the wall mount tray and wiring 4 or more units.

Typography

In this manual, typography is used as indicated below:

Bold

is used to emphasize words and to indicate connector

names of the unit.

Italic

is used to emphasize the paragraph title in cross-

references.

«
...
4
5
6
7
8
...
»

Содержание SAILOR 6080













































Отзывы:

Нет отзывов