manualshive.com logo in svg

COBHAM GR740, Руководство пользователя

Пользовательский мануал COBHAM GR740 доступен для загрузки бесплатно на нашем сайте. Этот руководство содержит полезные инструкции по использованию продукта. Не забудьте скачать его с manualshive.com. Узнайте больше о продукте, изучив данное руководство.

Поделиться
Скачать
background image

GR740-UM-DS, Nov 2017, Version 1.7

183

www.cobham.com/gaisler

GR740

Table 175. 

0x00000004-0x00000030, 0x00000080-0x000003FC - RTR.RTPMAP - Routing table port mapping, addresses 

1-12 and 32-255

31

13 12

1

0

RESERVED

PE

PD

0x00000

N/R

N/R

r

rw

rw

31: 13

RESERVED

12: 1

Port enable bits (PE) - When set to 1, each bit enables packets with the physical / logical address corresponding 
to this RTR.RTPMAP register to be sent on the port with the same number as the bit index. For physical 
addresses, the bit index corresponding to the port with the same number as the physical address itself is always 
1. For logical addresses, at least one bit in this field must be set in order for packets with the corresponding log-
ical address to be routed.

0

Packet distribution (PD) - When set to 1, packet distribution is used for the physical / logical address corre-
sponding to this RTR.RTPMAP register. When set to 0, group adaptive routing is used. See section 13.2.6 and 
13.2.7 for more information.

NOTE: After reset, or after writing a RTR.RTPMAP register to zero, the register is considered invalid. For incoming pack-
ets with a logical address this means that the packet is spilled, and an invalid address error generated. For physical addresses 
this means that the RTR.RTPMAP register will not be used when routing the packet, and the packet is routed to the port that 
matches the physical address.

Table 176. 

0x00000404-0x00000430, 0x00000480-0x000007FC - RTR.RTACTRL - Routing table address control, 

addresses 1-12 and 32-255

31

4

3

2

1

0

RESERVED

SR EN PR HD

0x0000000

*

*

*

*

r

rw rw rw rw

31: 4

RESERVED

3

Spill-if-not-ready (SR) - When set to 1, an incoming packet with the corresponding physical / logical address is 
immediately spilled if the selected output port’s link interface is not in run-state. If packet distribution is used for 
the incoming packet, and this bit is set, the packet is spilled unless all output ports’ link interfaces are in run 
state. For physical addresses, this bit is double mapped in the RTR.PCTRL.SR field. Reset value for physical 
addresses is 0. Reset value for logical addresses is N/R.

2

Enable (EN) - Enables the routing table address control entry. Address control entries for physical addresses are 
always enabled, and this field is constant 1. For logical addresses, this bit must be set to 1 in order for packets 
with the corresponding logical address to be routed. Reset value for logical addresses is 0.

1

Priority (PR) - Sets the arbitration priority of this physical / logical address. 0 = low priority, 1 = high priority. 
Used when more than one packet is competing for the same output port. For physical addresses, this bit is double 
mapped in the RTR.PCTRL.PR field. Reset value for physical addresses is 0. Reset value for logical addresses is 
N/R.

0

Header deletion (HD) - Enables / disabled header deletion for the corresponding logical address. For physical 
addresses, header deletion is always enabled, and this bit is constant 1. Reset value for logical addresses is N/R.

Содержание GR740









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GR740

IEI Technology KINO-KBN-i2 Quick Installation Manual preview
KINO-KBN-i2
Бренд: IEI Technology Страницы: 21
Laurell WS-650 lite Series Operation Manual preview
WS-650 lite Series
Бренд: Laurell Страницы: 84
Texas Instruments ThunderLAN TNETE100A Programmer'S Manual preview
ThunderLAN TNETE100A
Бренд: Texas Instruments Страницы: 179
National Instruments Fieldpoint cFP-RTD-124 Operating Instructions Manual preview
Fieldpoint cFP-RTD-124
Бренд: National Instruments Страницы: 15
JETWAY HBJC924R3288DG2NS Series Quick Installation Manual preview
HBJC924R3288DG2NS Series
Бренд: JETWAY Страницы: 6
Kontron CPS3003-SA User Manual preview
CPS3003-SA
Бренд: Kontron Страницы: 19
ekwb 3831109810316 User Manual preview
3831109810316
Бренд: ekwb Страницы: 16
Z3 Technology FSDI-1XA User Manual preview
FSDI-1XA
Бренд: Z3 Technology Страницы: 83
ZALMAN ZM-RWB1 User Manual preview
ZM-RWB1
Бренд: ZALMAN Страницы: 6
Patton electronics ForeFront 2616RC Getting Started Manual preview
ForeFront 2616RC
Бренд: Patton electronics Страницы: 80
U-Media WST-375L User Manual preview
WST-375L
Бренд: U-Media Страницы: 42
Costar CR6420XDi Quick Manual preview
CR6420XDi
Бренд: Costar Страницы: 14
Extron electronics Network Device PIP 444 Specification Sheet preview
Network Device PIP 444
Бренд: Extron electronics Страницы: 2
Citizen CBM-606 User Manual preview
CBM-606
Бренд: Citizen Страницы: 29
Lenze MC-PBM Operating Instructions Manual preview
MC-PBM
Бренд: Lenze Страницы: 46
Magnescale MG80-EI Operating Manual preview
MG80-EI
Бренд: Magnescale Страницы: 73
AJA FS-HDR Installation And Operation Manual preview
FS-HDR
Бренд: AJA Страницы: 129
Lava LAVA 8255-PIO Datasheet preview
LAVA 8255-PIO
Бренд: Lava Страницы: 1

Бренды по названию

Популярные бренды

Загрузить еще бренды