Cobalt Digital Inc BBG-1002-UDX-FS Скачать руководство пользователя | Manualshive

Страница: 25 / 110

background image

BBG-1002-UDX-FS-OM (V1.0)

BBG-1002-UDX-FS PRODUCT MANUAL

2-1

Chapter 2

Chapter 2

Installation

Overview

This chapter contains the following information:

•

Installing the BBG-1002-UDX-FS (p. 2-1)

•

Rear Panel Connections (p. 2-2)

•

GPIO, Serial (COMM), and Analog Audio Connections (p. 2-5)

Installing the BBG-1002-UDX-FS

Note:

• Where BBG-1002-UDX-FS is to be installed on a mounting plate (or regular

table or desk surface) without optional frame Mounting Tray
BBG-1000-TRAY, affix four adhesive-backed rubber feet (supplied) to the
bottom of BBG-1002-UDX-FS in locations marked with stamped “x”. If feet
are not affixed, chassis bottom cooling vents will be obscured.

• Where BBG-1002-UDX-FS is to be installed with optional frame Mounting

Tray BBG-1000-TRAY, do not affix adhesive-backed feet.

Installing Using BBG-1000-TRAY Optional Mounting Tray

BBG-1000-TRAY

allows up to three BBG-1002-UDX-FS to be mounted and

securely attached to a 1 RU tray that fits into a standard EIA 19” rack
mounting location. Install BBG-1002-UDX-FS unit into tray as described and
shown here.

1.

If installing BBG-1002-UDX-FS using optional frame Mounting Tray
BBG-1000-TRAY, install BBG-1002-UDX-FS in tray as shown in Figure
2-1.

2.

Connect the input and output cables as shown in Figure 2-3.

«
...
23
24
25
26
27
...
»

Содержание BBG-1002-UDX-FS















































































































Отзывы:

Нет отзывов

Похожие инструкции для BBG-1002-UDX-FS

Бренд: ABB Страницы: 78

Бренд: YASKAWA Страницы: 128

Бренд: Champion Global Power Equipment Страницы: 40

Бренд: Tvone Страницы: 18

Бренд: Littfinski Daten Technik Страницы: 2

Бренд: Pixelfly Страницы: 12

Бренд: Diehl Страницы: 28

Бренд: Puls Страницы: 27

Бренд: SMA Страницы: 272

Бренд: Questyle Audio Страницы: 14

Бренд: Kora Страницы: 36

Бренд: Wavtech Страницы: 12

Бренд: Telefunken Страницы: 34

Бренд: Quantum Harvest Страницы: 33

Бренд: ADF Web Страницы: 17

Бренд: ADF Web Страницы: 20

Бренд: ADF Web Страницы: 19

Бренд: ADF Web Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды