manualshive.com logo in svg

Cobalt Digital Inc 9922-FS, Руководство по эксплуатации продукта, Страница: 109 / 118

Поделиться
Скачать
Cobalt Digital Inc 9922-FS Скачать руководство пользователя страница 109

9922FS-OM (V1.5)

9922-FS PRODUCT MANUAL

3-67

Operating Instructions

Troubleshooting

9922-FS Card Edge Status/Error Indicators and Display

Figure 3-7 shows and describes the 9922-FS card edge status indicators and 
display. These indicators and the display show status and error conditions 
relating to the card itself and remote (network) communications (where 
applicable). Because these indicators are part of the card itself and require no 
external interface, the indicators are particularly useful in the event of 
communications problems with external devices such as network remote 
control devices.

Figure 3-7  9922-FS Card Edge Status Indicators and Display

9922-FS

4-Character Alphanumeric Display

COM

REF

ERR

IN A

IN B

IN C

IN D

Input Active

Indicators

Status/Error

Indicators

Item

Function

Alphanumeric
Display

Shows card statuses (

BOOT

 (card booting), (

9922-FS

 (card up and OK))

COM LED

Blue LED flashes when 9922-FS is receiving control message from remote network control (e.g., 
DashBoard™ or Cobalt

®

 Remote Control Panel)

REF LED

Blue LED illuminates indicating 9922-FS is receiving selected reference when set up for framesync 
operation.

ERR LED

This function is currently reserved.

Input Active 
LEDs

Blue LEDs for each SDI input (A thru D) indicate signal presence for each corresponding card SDI input. No 
illumination of any of the LEDs indicates the 9922-FS has not locked onto a valid signal on any input.

Содержание 9922-FS























































































































Отзывы:

Нет отзывов