Coast Spas CURVE APEX, Руководство пользователя, Страница: 30 / 57

OWNER’S MANUAL 202 1
3 0
The Main Menu
PRIMING THE PUMPS
As soon as the Priming Mode screen appears on the panel, select
the “Jets 1” button once to start Pump 1 in low-speed and then
again to switch to high-speed. Also, select the other pumps, to
turn them on. The pumps should be running in high-speed to
facilitate priming. If the pumps have not primed after 2 minutes,
and water is not flowing from the jets in the spa, do not allow the
pumps to continue to run. Turn off the pumps and repeat the
process.
Note: Turning the power off and back on again will
initiate a new pump priming session. Sometimes momentarily
turning the pump off and on will help it to prime. Do not do this
more than 5 times. If the pump(s) will not prime, shut off the power
to the spa and call for service.
Important: A pump should not be
allowed to run without priming for more than 2 minutes. Under NO
circumstances should a pump be allowed to run without priming
beyond the end of the 4-5 minute priming mode. Doing so may
cause damage to the pump and cause the system to energize the
heater and go into an overheat condition.
EXITING PRIMING MODE
The system will automatically enter the normal heating and
filtering at the end of the priming mode, which lasts 4-5 minutes.
You can manually exit Priming Mode by pressing the “Exit” button
on the Priming Mode Screen. Note that if you do not manually exit
the priming mode as described above, the priming mode will be
automatically terminated after 4-5 minutes. Be sure that the pump
(s) have been primed by this time. Once the system has exited
Priming Mode, the top-side panel will display the Main Screen, but
the display will not show the temperature yet, as shown below.
This is because the system requires approximately 1 minute of
water flowing through the heater to determine the water
temperature and display it.
NAVIGATION
Navigating the entire menu structure is done by touching the
screen. When a text item is shown in white on the main screen, it
is selectable. The menu selections on the right side of the
screen can be selected. Select one of these to enter a different
screen with additional controls. Most menu screens time out and
revert to the main screen after 30 seconds of no activity. The
only item that can be changed on the left side of the Main
Screen is the Set Temperature. Touch either the set temperature
line or the water temperature to go to the Set Temperature
screen.
TIME-OF-DAY
Be sure to set the Time-of-Day
Setting the time-of-day is important for determining filtration
times and other background features. “Set Time” will appear on
the display if no time-of-day is set in the memory. On the
Settings Screen, select the Time-of-Day line. On the Time-of-
Day screen, simply select the Hour, Minutes, and 12/24 Hour
segments. Use the Up and Down Buttons to make changes.
Note: This only applies to some systems: If power is
interrupted to the system, Time-of-Day will be maintained for
several days.
JETS
The Spa Screen shows all available equipment to control, as
well as other features, like Invert. The display shows icons
that are related to the equipment installed on a particular spa
model, so this screen may change depending on the
installation. The icon buttons are used to select and control
individual devices. Some devices, like pumps, may have more
than one ON state, so the icon will change to reflect the state
that the equipment is in. Below are some examples of 2-speed
Pump indicators.
If the Spa has a Circ Pump, a Circ Pump Icon will appear
to indicate its activity, but outside of Priming Mode, the Circ
Pump cannot be controlled directly.
Note:
The icon for the
pump that is associated with the heater (Circ or P1 Low) will
have a red glow in the center when the heater is running.
LUXURY SERIES CONTROL PANEL
CURVE COLLECTION