background image

COAIRE, Div. of Quietside Corporation

4

Please be Please be aware of the dangers that can be caused. If the

danger can not be prevented, loss of life or injury can be caused.  

Please install the product in areas free of explosives (acetylene, propane

gas, etc) or flammable substances. In case of operating the product in

flammable environment, fire or explosion can be caused. 

Please make sure the circuit breaker has been powered down before

inspection or repairing or maintenance work. If you perform inspection

or repair without powering down the circuit breaker, electric shock or

injury can occur. When connecting power, make sure to use Crimp-Type

terminal. Please check the connecting area and supply power after all

procedures have been completed. Always comply to the National

Electric Code and any local requirements. 

When the circuit breaker is turned on during the operation, do not

touch the rotating parts (fan, pulley, belt, etc). Your hand may get stuck

to the product. When the compressor is operating, the product will be

operated or stopped automatically based on the pressure. Please be

aware of the danger.  

Compressed air has great power. Flying parts can cause serious injury.

Before stopping the compressor, always make sure to turn off the main

power and eliminate the pressure of all elements related to the

compressor or pipes. 

In closed space, install compressor ventilation fan and maintain the

ambient temperature below 104’F (40°C) and please make sure the

average temperature is below 85’F (30°C). Please install the product in

areas free from direct sunlight, rain, dust, corrosion or toxic gas.

Operating in inappropriate areas can cause product deterioration or

damages.  

When opening the door or disassembling the panel for inspection, repair

or maintenance during or after operation, do not touch the product

directly. And do not insert flammable substance in hot areas such as

discharge pipe, after-cooler, basic compressor, etc. There can be danger

of fire or burns. 

Do not modify the compressor. Do not use the product for purpose

other than air compression. Product can deteriorate or be damaged.

Please use standard parts for parts replacement related to the

compressor repair. Consult your distributor  

1. CAUTIONS 

Содержание CSOF-S3PL(H)





























Отзывы: