Co2meter AZ 77535 Скачать руководство пользователя страница 3

Страница: 3 / 14

MATERIAL SUPPLIED

Meter
4pcs AA batteries
Operation manual
Hard carrying case

This package contains:

Optional accessory:

33% calibration salt (VZ0033AZ1)
75% calibration salt (VZ0075AZ1)

RS232 cable and software

Adaptor (9V/100~240Vac)

POWER SUPPLY

The meter is powered by either 4 AA
batteries or a DC adaptor(9V/1A output).

Install the batteries into the battery
compartment on the rear and make sure
they are in correct polarity and good
contact.

“Lob” will appear on the LCD

And beeper sounds.

atter

When an adaptor is used, it will

cut off the power supply from batteries.
The adaptor can’t be used as a battery
charger.

When battery voltage gets low, a

(Fig.1)

The CO sensor

can’t work under low voltage, so it beeps
to indicate failed CO measurement

(press any key but to stop the beeps)
and the readings won’t be displayed.
Please replace with fresh b

ies or

connect with an adaptor.

7752/77532

7755/77535

Fig.1

SET

Содержание AZ 77535















Результаты поиска

Содержание AZ 77535

Отзывы:

Похожие инструкции для AZ 77535

Бренды по названию

Популярные бренды

Co2meter AZ 77535, Руководство по эксплуатации

Результаты поиска

Содержание AZ 77535

Отзывы:

Похожие инструкции для AZ 77535

Бренды по названию

Популярные бренды