UNITIZED TRANSAXLE (GASOLINE VEHICLE)
General Information
24
F
N
R
C l u b C a r
552
Figure 24-3
Shifter Positions (Top View)
553
Figure 24-4
Lubricant Level (should be level with bottom
of hole) and Drain Plug
TOOLS REQUIRED FOR THIS SECTION
Hydraulic floor jack (or chain hoist)
12 to 18 in. straight edge
17 mm socket, 3/8-in. drive
Jack stands (2) (one ton capacity)
Small ball peen hammer (10 oz.)
7/16-in. combination wrench
Hydraulic press
Plastic or rubber mallet
1/2-in. combination wrench
Bench vise
Ratchet wrench, 3/8-in. drive
9/16-in. combination wrench
Standard slip joint pliers
Torque wrench, 3/8-in. drive
11/16-in. combination wrench (2)
External snap ring pliers (0.070 in. tip)
3/8-in. Socket, 3/8-in. drive
17 mm combination wrench
External snap ring pliers (0.047 in. tip)
7/16-in. Socket, 3/8-in. drive
Small flat blade screwdriver
90° Internal snap ring pliers (0.090 in. tip)
10 mm Combination wrench
Medium flat blade screwdrivers (2)
Feeler gauge
1/2-in. Socket, 3/8-in. drive
No. 2 phillips-head screwdriver
16-in. rolling head prybar
9/16-in. Socket, 3/8-in. drive
1/4-in. nut driver
Small punch or scratch awl
5/8-in. Socket, 3/8- in. drive
5/16-in. nut driver
1/4-in. diameter drift or metal rod
12 mm Socket, 3/8-in. drive
Small knife or wire snippers
Bearing puller wedge attachment (P/N 1012812)
Axle seal tool (P/N 1014162)
Governor gear shaft installation tool (P/N
101933101)
10 mm socket, 3/8-in drive
Internal snap ring pliers (P/N 1012560)
Brake cable removal tool (P/N 102555501)
13 mm combination wrench
LUBRICATION
There are two oil port plugs located on the right (driven clutch) side of the unitized transaxle
When the vehicle is on a level surface, use the upper plug as a lubricant level indicator. Lubricant level should be
even with the bottom of level indicator hole. Use the lower plug for draining. When draining lubricant, remove both
plugs to allow the lubricant to drain faster. Clean and reinstall the drain plug and gasket before filling the transaxle with
new lubricant. Use a funnel when filling the transaxle through the lubricant level indicator hole. Fill with 27 oz (0.8 L)
80-90 WT. API class GL or 80-90 WT. AGMA class 5 EP gear lubricant (or until lubricant begins to run out of the level
indicator hole). Tighten the plug to 20 ft·lb (27.1 N·m).
2014 Precedent
®
Golf Car Maintenance and Service Manual
Page 24-3
Содержание Precedent 2014
