Club Car FE 350, Дополнение к руководству по обслуживанию и ремонту

Страница: 68 / 280

11
Test Procedures TROUBLESHOOTING AND ELECTRICAL SYSTEM
TEST PROCEDURE 9 – Starter/Generator (Starter Function)
See General Warning on page 10-1.
1. Disconnect battery and spark plug wire(s). See Disconnecting the Battery – Gasoline Vehicles, Section 10,
Page 10-2.
2. Ensure that wires are connected correctly and are tight. If they are not, rewire or tighten as necessary.
3. Disconnect the wires from all the terminals on the starter/generator. Then place the black (–) probe of a
multimeter, set to 200 ohms, on the starter/generator housing (scratch through the finish to ensure a good
ground). While holding the black (–) probe against the housing, place the red (+) probe (one at a time) on the A1,
A2, F1, F2 and DF terminals respectively
(Figure 11-23, Page 11-26) . The readings should be no continuity. If
the readings are incorrect, the starter/generator will need to be removed from the vehicle and disassembled by a
qualified technician.
See Starter/Generator Removal on page 12-1.
– An incorrect reading from the A1 or A2 terminal indicates three possible problems: 1) a grounded A1 or A2
terminal, 2) a grounded wire in the brush area, or 3) a grounded armature/commutator.
– If the F1 or F2 reading is incorrect, it indicates a possible grounded F1 or F2 terminal or a grounded field coil.
– If the DF reading is incorrect, it indicates a possible grounded DF terminal or a grounded field coil.
4. Disconnect the ground wire from the A2 terminal and the green wire from the A1 terminal on the starter/generator.
5. Using a multimeter set to 200 ohms, place the red (+) probe on the A1 terminal and the black (–) probe on the A2
terminal. The reading should be continuity. If the reading is incorrect, a possible open or poor contact in a brush
assembly and/or open armature windings may be the cause. The starter/generator will need to be removed from
the vehicle and disassembled by a qualified technician.
See Starter/Generator Removal on page 12-1.
6. With the wires still disconnected, using a multimeter set on 200 ohms, place the red (+) probe on the F1 terminal
and the black (–) probe on the F2 terminal. The reading should be between approximately 0.1 and 0.3 ohms. If
the reading is incorrect, a possible open field coil or bad connections at terminals may be the cause. The
starter/generator will need to be removed from the vehicle and disassembled by a qualified technician.
See
Starter/Generator Removal on page 12-1.
7. With the wires still disconnected, using a multimeter set to 200 ohms, place the red (+) probe on the DF terminal
and the black (–) probe on the F1 terminal. The reading should be between 4.5 and 5.5 ohms. If the reading is
incorrect, a possible grounded DF terminal and/or grounded field coil may be the cause. The starter/generator
will need to be removed from the vehicle and disassembled by a qualified technician.
See Starter/Generator
Removal on page 12-1.
8. Connect battery and spark plug wire(s). See Connecting the Battery – Gasoline Vehicles, Section 10, Page
10-3.
2m
20
m
200
m
2k
200
200
200 200
20
2
200
m
500
20k
200k
2000
k
1000
OFF
WAVETEK 5XL
V
V
V
A
! !
COM 200nA
MAX
1000 ---
750V
FUSED
F2
DF
F1
A2
A1
1
2
1. Yellow Wire 2. 200 Ohm Setting
F2
DF
F1
A1
A2
1
2
1. Yellow Wire 2. Jumper Wire
461
Figure 11-23 Check Starter Terminal Continuity
462
Figure 11-24 Jumper Wire Ground – DF to A2
Page 11-26 2009 FE 350 Maintenance and Service Supplement