background image

 

Rear Fender Installation

 

10       2001 Carryall 2 XRT Owner’s Manual Supplement

 

3. Position a fender in the vehicle, align the hole in the fender with the slot in the frame as shown and install

bolt (1), flat washers (2), and locknut (3) 

 

(Figure 1)

 

. Finger-tighten only at this time. 

4. Make sure fender is correctly aligned in the vehicle.

4.1. Make sure outer fender rib is flush with the inside surface of the upper side panel 

 

(Figure 2)

 

4.2. Move fender as far forward as possible. There should be no gap between the fender and side

panel

 

 (Figure 2)

 

.

5. Drill three 5/16 inch holes through the fender using existing frame holes as guides 

 

(Figure 2)

 

.  

6. Install bolt (1), large flat washers (2), and locknut (3) at top hole as shown 

 

(Figure 2)

 

. Tighten mounting

hardware at both upper holes to 35 in-lb (4.0 N·m).

7. Install bolt (1), large flat washer (2), small flat washer (4) and locknut (3) in both forward-facing holes in

frame and fender 

 

(Figure 2)

 

.  Tighten to 35 in-lb (4.0 N·m).

8.  Repeat steps 3 - 7 for the other rear fender.

9. Lower cargo bed.   

 

Figure 2   Drill Additional Mounting Holes

2

2

3

2

1

3

4

1

Before drilling holes, 
move fender as far 
forward as possible.

Do not allow any gap
between fender and 
side panel.

FENDER RIB

UPPER 
SIDE PANEL

Содержание CARRYALL 2 XRT













Отзывы: