Clipper CM 501 HONDA Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 24

Clipper CM 501 HONDA Скачать руководство пользователя страница 13

VERS. 2017.06.21

CM 501 TH_MAN_EN

13

3

ASSEMBLY AND COMMISSIONING

The machine is delivered fully equipped and assembled (although without diamond blade) and is
ready for operation after connection to the appropriate power supply.

3.1 Tool assembly

Only NORTON blades with a maximum diameter of 500 mm can be used with the CM501.
All tools used must be selected with regard to their maximum permitted cutting speed for the
machine’s maximum permitted rotation speed.
Before mounting a new blade into the machine, switch off the machine and isolate it from the main
source of electricity.

To mount a new blade, follow these steps:



Open the shaft vent cover on the blade guard.



Loosen the hexagonal nut on the blade shaft, which holds the removable outer flange.



Remove the outer flange.



Clean the flanges and blade shaft and inspect for wear.



Mount the blade on arbor ensuring that direction of rotation is correct. Wrong direction of rotation

blunts the blade quickly.



Replace outer blade flange.



Tighten hexagonal nut with spanner supplied for this purpose.



Shut the vent cover.

The blade bore must correspond exactly to the diameter of the blade shaft. Cracked or damaged
bore is dangerous for the operator and for the machine.

3.2 Water cooling system

Fill  the  water  pan  with  clean  water  to  approximately  2cm  from  top  (ensure  that  bottom  of  pump  is
fully immersed in water).
Open water-tap at blade guard (note that handle on water-tap should be in line with water-flow).
Ensure  that  water  is  flowing  freely  in  the  circuit  and  is  delivered  adequately  to  both  sides  of  the
blade, as insufficient water supply may result in premature failure of the diamond blade.
The water pump must never run without water. Always make sure that there is enough water in the
pan and refill if necessary.
In case of frost, empty the water cooling system from its water.

«
...
11
12
13
14
15
...
»

Содержание CM 501 HONDA

























Отзывы:

Нет отзывов