(adjustable directions)
Max 10” or 255mm
Min 3” or 76mm
(Toggle Plate)
(Secondary saftey lock)
(notches)
(notches)
(Toggle Plate)
(Secondary saftey lock)
(rollers)
(rollers)
30° MAX
ACCEPTABLE LOADING
DECK/FLOOR/GROUND LEVEL
WORK SURFACE
WORK SURFACE
* DO NOT WORK *
ABOVE ANCHOR POINT
MINIMUM CLEARANCE 3ft (1m)
W
A
RNING!!! SWING F
ALLS C
AN OC
CUR
WHEN
THE
W
O
RKIER IS NO
T DIREC
TL
Y UNDER ANCHOR POINT
.
Product Warranty, Limited Remedy and Limitation of Liability
WARRANTY: THE FOLLOWING IS MADE IN LIEU OF ALL WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OR CONDITIONS
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Equipment offered by ClimbTech is warranted against factory defects in workmanship and materials for
a period of 5 year life cycle from date purchase or first use by the original owner.
LIMITED REMEDY:
Upon notice in writing, ClimbTech will repair or replace all defective items at ClimbTech’s sole discretion. ClimbTech reserves the right to require that the
defective item be returned to its plant for inspection before determining the appropriate course action. Warranty does not cover equipment damage resulting from wear,
abuse, damage in transit, failure to maintain the product or other damage beyond the control of ClimbTech. ClimbTech shall be the sole judge of product condition and
warranty options. This warranty applies only to original purchaser and is the only warranty applicable to this product. Please contact ClimbTech technical service department
for assistance.
LIMITATION OF LIABILITY: IN NO EVENT WILL CLIMBTECH BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES INCLUDING, BUT
NOT LIMITED TO LOSS OF PROFITS, IN ANY WAY RELATED TO THE PRODUCTS REGARDLESS OF THE LEGAL THEORY ASSERTED.
Inspection:
Official periodic inspection must be made at least annually. The inspection must be performed by a qualified person other than the
intended user. If severe weather or conditions exist then inspections must be carried out more frequently.
1.
Inspect beam anchor to make sure the rollers ride flush with mounting surface and roll smoothly.
2.
Make sure all labeling is affixed to the unit.
3.
Inspect anchoring system for signs of damage or wear.
4.
Make sure the unit can adjust and lock properly on to beam flange.
5.
Record inspection results in the space provide above.
*If any damage that could affect the strength or operation or unsafe conditions are found proper disposal is required. The
anchorage connector must be rendered unusable and then properly discarded.
INSPECTION AND MAINTAINANCE LOG
MODEL NUMBER:
DATE OF MANUFACTURE:
Part Number
Comments
Inspector Name
Date
Installation:
1.
Locate a structural steel beam flange capable of withstanding a 5,000-lb.
Static load or meeting OSHA 1926.502 requirements for a safety factor of
two. (Max beam flange thickness of 7/8” or 23mm) Mounting location must
be approved by a Engineer or qualified person.
2.
Push up on the toggle plate to allow the adjustable rollers to move.
3.
Fit the rollers over the edges of the beam flange, keeping the unit perpen-
dicular to the beam.
4.
Slide the adjustable rollers so that both sets of rollers are full resting on
the beam flange.
5.
Release the toggle plate and pull back on the adjustable rollers to ensure
the ratchet teeth are fully seated in the nearest ratchet notches.
6.
Tug, rock, and twist the anchor in all directions to ensure that it cannot
come off of the flange.
7.
Screw tight the secondary saftey locking screws on the bottom of the
toggle plate to insure the rollers can not move off the edge of the flange.
8.
The rollers must ride on a clear surface. Remove any dirt and grit if nessary.
9.
Ensure that Beam Trolley can not slide off the end of the beam it is
attached too. Install stoppers if necessary.
*Always re-adjust according to steps 1-9 above when moving to a new
or different size beam.
Performance:
Static tensile strength:
5000-lbf
(22kN) minimum.
Maximum capacity:
one worker with
max weight of 310-lbs when used as a
single point anchorage connector for
personal fall arrest or restraint system.
Dimensions:
Weight:
7.7-lbs
Beam flange width range:
3”-10”
Beam flange thickness:
Up to 7/8”
Regulatory compliance:
OSHA 1910.66 & 1926.502 ANSI
Z359.1-2007, Z359.7-2011 / EN 795:1996
Component Materials:
Aluminum:
cross bar, rollers,
Polyester:
webbing,
Zinc Plated Steel:
swivel,
Stainless Steel:
spring, hardware
*All products subjected to fall arresting forces should be
removed from service immediately!
USE AND INSTALLATION INSTRUCTIONS
BEAM TROLLEY
Aluminum, Zinc Plated Steel,
Stainless Steel
(1) person 310-lbs
Model: BTA
012
N
1-(888)-206-1318
Lot: xxx MFG: mm/yyyy
(ANCHOR POINT)
30° MAX
(5,000-lbf Swivel)
V1.3
WARNING:
All persons using this equipment must read,
understand and follow all instructions. Failure to do so may
result in serious injury or death.
(INSPECT BEFORE USE)
COMPLIANCE:
OSHA 1910.66 & 1926.502 ANSI Z359.1-2007
Z359.7-2011
CE 0321 / EN 795:1996 (+A1:2000) Class B
