Climax H&S TOOL SPEED FACER ODF100 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 132

background image

P/N 102615, Rev. 0

Page 31

F

IGURE

3-3. M

OUNTING

ARRANGEMENTS

3.3.1

Horizontal mounting

The hazard with horizontal mounting is the machine
falling down until it hits the bridge weldment.
Mitigations include one of the following arrangements:

•

Leave the setup fingers in place on the top of
the leveling feet.

•

If the setup fingers must be removed, block the
machine up from below or secure the machine
to anchor points above the machine using a
minimum of two opposite swivel hoist rings with
the customer-supplied anchor points and slings
rated for the machine weight and sling angle.
See Figure 3-3.

3.3.2

Vertical mounting

The hazard with vertical mounting is the machine falling
off the flange.

Mitigations include one of the following arrangements:

•

Install the setup fingers on the back of the
flange, on the “bottom” of the leveling feet
(see Figure 3-4).

F

IGURE

3-4. A

LTERNATE

MOUNTING

HOLES

•

If the flange is too thick to allow for the use of
the setup fingers, secure the machine to anchor
points above the machine using a minimum of

80°

OVERHEAD

MOUNTING

10°

15°

75°

HORIZONTAL

MOUNTING

VERTICAL

FLANGE

MOUNTING

HORIZONTAL AXIS

VERTICAL

AXIS

ALTERNATE
MOUNTING HOLES

«
...
47
48
49
50
51
...
»

Содержание H&S TOOL SPEED FACER ODF100





































































































































Отзывы:

Нет отзывов

Похожие инструкции для H&S TOOL SPEED FACER ODF100

Бренд: ParaBody Страницы: 5

Бренд: Sagola Страницы: 20

Бренд: Earmor Страницы: 5

Бренд: AccuMed Страницы: 14

Бренд: TAS Страницы: 25

Бренд: Danelec Страницы: 67

Бренд: dbx Страницы: 2

Бренд: Eagle Group Страницы: 8

Бренд: Eaton Страницы: 16

Бренд: Eaton Страницы: 6

Бренд: Ecco Страницы: 17

COOPER POWER SERIES

Бренд: Eaton Страницы: 8

Бренд: Konica Minolta Страницы: 32

Бренд: QRS Страницы: 16

Бренд: QMAXZ Lighting Страницы: 36

Marathon Multi600

Бренд: Saeyang Страницы: 21

Бренд: S&C Страницы: 11

Бренд: Agilent Technologies Страницы: 114

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды